Purpose Of Use; Technical Specifications - TESY GCA Serie Instrucciones De Uso Y Mantenimiento

Dear Clients,
The TESY team would like to congratulate you on your
new purchase. We hope that your new appliance shall
bring more comfort to your home.
This technical description and instructions manual was
prepared in order to acquaint you with the product
and the conditions of proper installation and use. These
instructions were also intended for use by qualified
technicians, who shall perform the initial installation, or
disassembly and repairs in the event of a breakdown.
The observance of the instructions contained herein is
in the interest of the buyer and represents one of the
warranty conditions, outlined in the warranty card.
The electric water heater complies with the
requirements of EN 60335-1, EN 60335-2-21.
I.

PURPOSE OF USE

The appliance is designed to supply hot water to
household facilities equipped with a piping system
operating with pressure not greater than 6 bars
(0.6 Mpa).
The appliance is designed to function in closed, heated
premises and is not designed to operate at constant
flow regime.
II.

TECHNICAL SPECIFICATIONS

•
Nominal volume V, liters - see the appliance's rating
plate
•
Nominal voltage - see the appliance's rating plate
•
Nominal power consumption - see the appliance's
rating plate
•
Nominal pressure - 0.75 MPa
•
Water heater type - closed accumulating water
heater, with thermal insulation
•
Inner coating: enamel coating
•
Daily energy consumption - see Annex I
•
Rated load profile - see Annex I
•
Maximum temperature of the thermostat - see
Annex I
•
Default temperature settings - see Annex I
•
Energy efficiency during water heating - see Annex I
IMPORTANT RULES
III.
•
The water heater must only be mounted in premises
with normal fire resistance.
•
Do not switch on the water heater unless you
established it was filled with water.
•
Qualified P&P specialists and Electricians must only
perform the connecting of the water heater to the
water and electric mains. A qualified technician is
a person who has the competence according the
regulations of the country in question.
English
•
Upon connecting the water heater to the electric
mains care must be taken to connect the safety lead.
•
If the probability exists for the premise's temperature
to fall below 0°C, the water heater must be drained
(observe the procedure outlined in section V,
subsection 2 "Water heater's piping connection")
•
During operation - regime of heating the water - water
drops through the drainage opening of the protection
valve are usual. The protection valve should be left
open to the atmosphere. Measures should be taken
to lead and collect the leakages in order to prevent
damages, ensuring that this is in conformation with
the requirements described in p. 2 in paragraph V.
•
The valve and the elements linked to it must be
protected from freezing.
•
During the heating the appliance could produce a
hissing noise (the boiling water). This is common
and does not indicate any damage. The noise gets
higher with the time and the reason for this is the
accumulation of limestone. To remove the noise
the appliance must be cleaned from limestone. This
type of cleaning is not covered by the warranty.
•
In order to secure the water heater's safe operation,
the safety return-valve must undergo regular
cleaning and inspections for normal functioning /the
valve must not be obstructed/, and for the regions
with highly calcareous water it must be cleaned
from the accumulated lime scale. This service is not
provided under warranty maintenance.
•
All alterations and modifications to the water
heater's construction and electrical circuitry are
forbidden. If such alterations or modifications are
established during inspection, the appliance's
warranty shall be null and void. Alterations and
modifications shall mean each instances of removal
of elements incorporated by the manufacturer,
building in of additional components into the water
heater, replacement of elements by similar elements
unapproved by the manufacturer. These instructions
shall also apply to water heaters equipped with a
heat exchanger
•
All alterations and modifications to the water
heater's construction and electrical circuitry are
forbidden. If such alterations or modifications are
established during inspection, the appliance's
warranty shall be null and void. Alterations and
modifications shall mean each instances of removal
of elements incorporated by the manufacturer,
building in of additional components into the water
heater, replacement of elements by similar elements
unapproved by the manufacturer.
•
These instructions shall also apply to water heaters
equipped with a heat exchanger.
•
If the power supply cord (of models that have
one) is damaged, it must be replaced by a service
representative or a person with similar qualification,
to avoid any risk.
Instructions for use and maintenance
EN
7