Special Accessories; Technical Data - Martin Yale papermonster L163 Instrucciones De Uso

GB
EMPTYING THE RECEPTACLE (fig. 3):
A two compartment receptacle ensures that
waste is separated. It consists of a paper
receptacle (8) and a separate collection tray (9)
for the shredded CDs, DVDs and FDs.
When the shredded material becomes visible in
the "receptacle full" window (10) (fig. 3) it is time
to empty the receptacle.
Proceed as follows:
- Pull the receptacle (8) with the collection tray
(9) out of the lower housing.
- Dispose of the contents of the containers
separately.
- Push the empty receptacle with the collection
tray back into the lower housing.
When shredding large quantities
of CDs/DVDs/FDs (approx. 10 per
load), please check the fill level of the
collection tray occasionally and empty
the tray separately as required.
Note: The machine only runs when the receptacle
is fully pushed in!
MATERIAL JAM IN THE MACHINE:
If too much paper is fed to the cutting system the
cutting system will jam.
Proceed as follows:
- Briefly press the backwards button (3).
- Cutting system runs in reverse, frees excess
material and stops.
Paper jam in paper feed slot (6)
- Remove released paper from the feed slot
(6).
- Continue shredding with lower quantity of
paper.
Material jam in CD/DVD/FD feed slot (7)
- Remove released material.
Take care when removing material
as sharp edges may cause injury!
- If necessary, operate the cutting mechanism
manually forwards and backwards alternately
until the material has completely run through
and has been shredded.
Wait each time until the motor stops
before switching direction!
Description
Lubrication bottle, 110 ml
Note: For orders of special accessories and spare parts, please contact your dealer.
OPERATION
10
MOTOR PROTECTION:
If the motor is overloaded, it switches off. Switch
the machine off with the pushbutton switch (1).
After a cooling down period of approx. 15-20
minutes (depending on the model and room
temperature), you can switch the machine on
again.
DISPOSING OF THE MACHINE:
Dispose
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.

SPECIAL ACCESSORIES

9
8
fig. 3
fig. 4
MALFUNCTION
DISPOSING
of the machine in
Order-No.
88035
5
MAINTENANCE
MAINTENANCE OF THE
CUTTING MECHANISM:
Cross-cut cutting mechanisms must be
oiled after a certain operating time (after
approximately 15 minutes of continuous
use).
Proceed as follows:
Spread some oil on a sheet of paper and then
feed it into the cutting mechanism through the
paper feed slot (6).
The paper is drawn in and the oil thus gets into
the cutting mechanism.
To re-order the special oil, see "SPECIAL
ACCESSORIES".
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (1) (fig. 1).
CHECKLIST IN THE EVENT OF FAULTS:
If the machine does not work, check the following
points:
- is the mains plug connected to the mains?
- is the pushbutton switch (1) switched on?
- is the receptacle pushed in?
- is the receptacle full?
Follow the instructions in "EMPTYING THE
RECEPTACLE".
- is there a material jam in the machine?
Follow the instructions in "MATERIAL JAM IN
THE MACHINE".
- Has the motor been overloaded?
See "MOTOR PROTECTION".
If none of the above applies, please contact
your dealer.
an

TECHNICAL DATA

Cutting width:
Cutting capacity:
Supply voltage:
Working width:
Noise generation:
Power:
Intermittent operation:
Dimensions (WxDxH):
Weight:
L163
4x33 mm
10 sheets (70g/m 2 )
9 sheets (80g/m 2 )
see name plate
220 mm
64-65 dB(A)
see name plate
2 min ON
20 min OFF
330x218x456 mm
approx. 6,2 kg