Nilfisk-Advance Micromatic 14 Instrucciones De Uso página 4

ENGLISH
120 VAC Grounding Instructions
This appliance must be grounded. If it should electrically malfunction
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock This appliance is equipped with a cord having an
equipment-grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
!
Danger!
Improper connection of the equipment-grounding conductor can result in
a risk of electric shock Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the appliance. If it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding
plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used~to connect this plug to a
2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not
available. The temporary adapter should be used only until a properly
grounded outlet (Figure 1) can be installed by a qualified electrician. The
green-colored rigid ear, tab or the like extending from the adapter must
be connected to a permanent ground such as a properly grounded outlet
box cover. Whenever the adapter is used, it must be held in place by a
metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenNellow) wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to the grounding pin only.
Extension cords connected to this machine should be 12 gauge, three-wire
cords with three-prong plugs and outlets. DO NOT use extension cords
more than 50 feet (15 m) long.
Introduction
This manual will help you get the most from your Advance Micromatic 14E .
Read it thoroughly before operating the machine. Specifications and
details are subject to change without prior notice.
Parts and Service
Repairs, when required, should be performed by Advance service
personnel using Advance original replacement parts and accessories. Call
Advance for repair parts or service Please specify the Model and Serial
Number when discussing your machlne.
Name Plate
The Model and Serial Number of your machine are shown on the
Nameplate on the back panel of the machine. This information is needed
when ordering repair parts for the machine. Use the space below to note
the Model and Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton so
that it can be inspected by the carrier that delivered it. Contact the carrier
immediately to file a freight damage claim.
Caution and Warnings
Symbols
Advance uses the symbols below to signal potentially dangerous
conditions. Always read this information carefully and take the necessary
steps to protect personnel and property.
!
Danger!
Is used to warn of immediate hazards that will cause severe personal injury
or death.
!
Warning!
Is used to call attention to a situation that could cause severe personal
injury.
!
Caution!
Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property.
When using an electrical appliance, basic precautions should always be
followed, including the following:
Read all instructions before using this machine.
This product is intended for commercial use only
!
Warning!
To reduce the risk of fire, electric shock or injury:
1 . The Advance floor cleaning machine and the accessories supplied by
the manufacturer are suitable for scrubbing hard floors. The use of
non-Advance accessories may impair the safe operation of the
machine.
2 . Do not use the machine for:
- Dry cleaning, Carpet cleaning, Shampooing, Outdoor cleaning
3 . Do not leave the machine when it is plugged in. Unplug the unit from
the outlet when not in use and before servicing.
4 . Do not allow machine to be used as a toy. Close attention is necessary
when operated near children.
5 . Use only as described in this manual. Use only the manufacturer's
recommended attachments.
6 . Do not use with damaged cord or plug. If the appliance is not working
as it should be, has been dropped, damaged, left outdoors or dropped
into water, return it to a service center.
7 . Do not pull or carry by cord, use cord as a handle, close a door on the
cord or pull the cord around sharp edges or corners. Do not run the
appllance over the cord. Keep the cord away from heated surfaces
8 . Do not expose to rain. Store indoors.
9 . Do not unplug by pulling on the cord. To unplug, grasp the plug, not
the cord.
10 . Do not handle the plug, cord or appliance with wet hands.
11 . Do not insert any object into openings. Do not use with any opening
blocked- keep free of dust, lint, hair, and anything that may reduce air
flow.
12 . Keep clothing, hairs, fingers, and all parts of body away from openings
and moving parts.
13 . Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes, or any health endangering dusts.
14 . Turn off all controls before unplugging.
15 . Do not use to pick up flammable or combustible liquids such as gasoline
or use in areas where they may be present.
16 . The voltage and frequency indicated on the name plate must
correspond to the wall recepticale supply voltage.
17 . For repairs, use original Advance spare parts only. The use of other
similar parts will automatically exclude the manufacturer's liability.
18 . When cleaning and servicing the machine, local or national regulations
may apply to the safe disposal of liquids which may contain: chemieals.
orease. oil. acid. alkalines ore other danaerous liquids.
❶
Know your Machine
1 . Display
2 . Handle bar
3 . Handle bar adjustment
4 . Rear grip position for transport
5 . Solution filter
6 . Tank top
7 . Solution tank
8 . Recovery tank
9 . Front grip position for transport
10 . Squeegee head
11 . Spray nozle
12 . Front squeegee
13 . Brush
14 . Rear squeegee
15 . Pre-filtervacuum motor
16 . Exhaustsound insulation
17 . Vacuum pre filter
❷
Brush Installation
!
Warning!
Moving parts - disconnect power before servicing
!
Caution!
The brush locking screw has a left hand thread
1 . Place brush opening on drive shaft and let engage.
1
08603313