Technical Specifications - Nilfisk-Advance Micromatic 14 Instrucciones De Uso

Ocultar thumbs

página de 14

/ 14
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

2 . Screw in safety screw with bushing and tighten brush.

❸

Brush pressure adjustment

+ more brush pressure = turn adjustment knob to the right

- less brush pressure

= turn adjustment knob to the left

❹

Filling the Solution Tank

1 . Fill the solution tank with 11 litres/ 3 gallons cleaning solution.

2 . Do not fill up the solution tank completely: 2.5 cm (1") should be left

free at the top of the tank

3 . The solution should be a mixture of water and a cleaning chemical

appropiate for the type of job.

4 . Always follow the dilution instructions on the chemical container label.

5 . The temperature of the cleaning solution must not exceed 40°C/100° F.

Caution!

Use only low-foaming, non-flammable liquid detergents intended for

machine application.

❺

Wet Scrubbing

1 . Sweep or vacuum floor first to remove litter

2 . Adjust handle bar to working position.

3 . Plug in machine to a properly grounded outlet

4 . Press the master switch ON. The brush motor will run

5 . Switch vacuum motor ON.

6 . Switch pump ON. The solution is supplied to the brush.

NOTE: Solution flow is pre-set

There are two switch positions.

min. - low solution supply

max. - high solution supply

7 . Press foot peddle down. Brush and squeegees are lowered to the floor.

8 . For best results, move machine at a slow walking speed. In case of

heavy soilage, scrub floor first with water and switch vacuum motor

OFF. Then scrub floor again and pick up the water (double scrub).

Caution!

To avoid damaging the floor, keep the machine moving while the

brush is turning.

9 . The recovery tank has an automatic float shut-off to prevent solution

from entering the vacuum system.

When the float closes, the recovery tank must be emptied.

The machine will not pick up water with the float closed.

10 . When the recovery tank is full turn the master switch OFF.

Take out recovery tank at the handle and drain it If machine has previously

been used, rinse tank with clean water.

❻

After Use

1 . Turn master switch OFF.

2 . Press the foot peddle down to raise brush and squeegee.

3 . Unplug machine

4 . Empty solution tank and rinse it with clean water.

5 . Empty recovery tank and rinse it with clean water.

6 . Inspect hoses and replace them if damaged.

7 . Remove brush and rinse it with clean water.

8 . Inspect squeegee inlet channels for litter and rinse them with clean

water.

9 . Inspect solution filter and vacuum pre-filter. Clean them or replace it if

damaged.

10 . Inspect vacuum exhaust filter. Clean it with air or replace it if clogged.

11 . Store the machine in a clean, dry place.

Maintenance schedule

Maintenance item

Clean and Inspect Tanks

Clean and Inspect Hoses

Clean Brush

Clean and Check Squeegees

Check Filters

Check Power Supply Cable

Check Spray Nozles

Vacuum Motor Carbon Brushes

❼

Squeegee Replacement

If the squeegee leaves narrow streaks of water, it is probably dirty or

damaged. Remove the squeegee, rinse it under clean water and inspect the

Once a

Once

Daily

Week

a year

squeegee blades.

Reverse or replace the squeegee blade if it is cut, torn, wavy or worn to a

radius.

To Reverse or Replace the Squeegee Blade:

1 . Unplug machine

2 . Remove tanks

3 . Tilt machine backwards

4 . Remove the two screws at nozle.

Take out nozle and exchange squeegees.

Trouble Shooting

There is no power. Motors do not work

1 . Check plug and cable

2 . Check main fuse

3 . Defective switch on operating panel

Brush motor does work brush does not turn

1 . Defective drive belt

2 . Brush not fixed

Inadequate suction

1 . Worn or defective squeegees

2 . Suction inlet clogged

3 . Suction hose loose, defective

4 . Tank lid defective

5 . Float valve jammed

6 . Vacuum pre-filters dirty

Poor cleaning

1 . Worn brush

2 . Brush to soft

3 . Walking too fast

4 . Water supply clogged

5 . Solution filter clogged

❽

Transport

1 . Unlock handle bar.

2 . Fold handle bar over the machine.

3 . Lock it.

Warning!

Do not carry the machine without a folded down handle bar.

Carry the machine only on the specified positions.

Accessories

1 . Scrubbing brush, Nylon, soft-medium~

2 . Scrubbing brush, Silicon Carbide, medium~*

*= standard

**= optional