EdilKamin AQUAMAXI 28 Instalación Uso Y Mantenimiento página 39

Practical advice
It is recommended to keep the radiators closed in the room
where the thermo replace is installed; The heat emitted from
the outlet may be suf cient to heat.
- An incomplete combustion process causes excessive fouling
on the heat exchanger pipe.
To prevent this you must:
- burn dry wood.
- ensure the hearth contains a bed of embers and burning car-
bon before adding more wood.
- place larger logs together with smaller ones.
- make sure the temperature of the return water is at least 50 °C
(use temperature control valve).
- Do not exceed the load values shown in the speci cation table
(page 28 under fuel consumption) since excessive loads can
create overheating problems.
N.B. N.B.
Seasoned wood has a heating capacity of about 4 kWh/kg, Seasoned wood has a heating capacity of about 4 kWh/kg,
while fresh wood has a heating capacity of only 2 kWh/kg. while fresh wood has a heating capacity of only 2 kWh/kg.
Therefore, for the same heating capacity double the quantity of Therefore, for the same heating capacity double the quantity of
fuel is needed. fuel is needed.
Water
content
g/kg of wood
Very
100
seasoned
seasoned
200
for 2 years
seasoned
350
for 1 year
Freshly
500
cut wood
recommended material: beech, oak, hornbeam and birch
Igniting the replace
To light the re the rst time, always use small pieces of wood. To light the re the rst time, always use small pieces of wood.
They burn more quickly and thus bring the replace to the cor- They burn more quickly and thus bring the replace to the cor-
rect temperature more quickly. rect temperature more quickly.
Use larger pieces of wood to refuel the re. Use larger pieces of wood to refuel the re.
Always place the wood well back in the replace, almost in Always place the wood well back in the replace, almost in
contact with the back wall of the same, so that even it if slips it contact with the back wall of the same, so that even it if slips it
will not touch the door. will not touch the door.
- Ensure that at least one radiator is always open.
- Actuate the switches of the electronic regulator.
- Place a pile of medium-thin dry wood in the thermo replace
and ignite the re.
- Wait a few minutes until it reaches suf cient combustion.
- Close the door
- Set the thermostat on the electronic regulator (*) at a tempera-
ture between 50 and 70° C.
NOTE: There may be a slight smell of paint the rst few times
it is ignited, however, this will disappear quickly.
Removing the ash (only when the re is out and the thermo Removing the ash (only when the re is out and the thermo
replace is cold) replace is cold)
Remove the ash with a dustpan or a vacuum cleaner. Remove the ash with a dustpan or a vacuum cleaner.
Place the ash only in non-combustible containers; remember that Place the ash only in non-combustible containers; remember that
remaining embers can re-light even 24 hours after burning. remaining embers can re-light even 24 hours after burning.
INSTRUCTIONS FOR USE
Heating Greater
capacity consumption
kWh/kg of wood %
4,5 0
4 15
3 71
2,1 153
- 39
MAINTENANCE
Cleaning the hearth
- The soot deposits that tend to accumulate on the internal walls
of the hearth decrease the ef ciency of heat transfer.
- It is therefore necessary to clean the replace regularly, by
bringing the water temperature to 80 / 85° C to soften the fou-
ling and then remove this with a steel spatula.
Glass cleaning
- Use an appropriate spray for ceramic glass to clean the glass
(Glasskamin - Edilakmin).
- The glass must be cleaned when cold.
- Before opening the door, make sure it is secured with the
lever at the top right (T - g. 4).
- For the opening swing of the door it is necessary to bring it in
the closed position.
- Insert the "cold handle" door handle on the latch between the
structure and the door and turn to open ( g. 5).
T
g. 4
g. 5
Removing the ceiling
The ceiling, made of refractory material, and can be removed
for cleaning.
NOTE ON THE DOOR GUIDES
The guides can be completely removed from the door (guides,
pulleys and counterweights).
For any requirements, please contact an Authorised Edilkamin
Technical Assistance Centre.
-