Peg-Perego Booklet 50 Instrucciones De Uso página 18

body or seat unit or car seat
attachment devices are correctly
engaged before use.
_ WARNING To avoid injury ensure
that the child is kept away
when unfolding and folding this
product.
_ WARNING Do not let the child
play with this product.
This product is not a toy.
_ WARNING The assembly and
preparation of the product must be
carried out by an adult.
_ Do not use this product if there are
parts missing or signs of breakage.
_ WARNING Never leave the child
unattended.
_ Always apply the brake when
stationary and when loading or
unloading children.
_ Do not insert fingers into the
mechanisms.
_ Be careful not to hurt the child
when adjusting the mechanisms
(handlebar, backrest ... ).
_ Any load applied to the handle and/
or the backrest and/or laterally to
the product can compromise the
stability of the product.
_ Do not load the baskets over 7
Kg. Do not put weight in the cup
holder (if present) in excess of
those indicated on the cup holders
themselves and never hot drinks. Do
not put loads of more than 0.2 Kg in
the hood pockets (if present).
_ Do not use the product near to
stairs or steps, heat sources, naked
flames or dangerous objects within
reach of the child.
_ Only replacement parts supplied or
recommended by the manufacturer/
distributor shall be used.
_ WARNING This product is not
suitable for running or skating.
_ WARNING Do not add any
mattress are not approved by the
manufacturer.
_ Do not use accessories which are
not approved by the manufacturer.
The images referring to the textile details may
differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS
1 OPENING: Before opening the frame, remove (without
using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER BEYOND ITS
LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY HANDLE OR
TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES TO THIS
FEATURE.
Press down the side fastener, hold the upper section of
the handle and rotate it towards you until the frame is fully
opened (fig_a). Open frame (fig_b).
The frame is properly opened when the attachment on the
base clicks into place, as shown.
2 FITTING THE WHEELS: Slot the uprights into the rear
wheel crosspiece (fig_a), ensuring that it is facing the
right way, then push the rear wheels on and make
sure that they click into place (fig_b). To mount the
front wheels, fit them into the uprights until they lock into
place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle tube
faces upwards, align it with the stroller (Fig_a).
Fasten the handle to the frame as shown in the figure
(Fig_b).
To complete the operation, press the two side buttons
on the handle (Fig_c) to ensure the handle pushes in
all the way, until it clicks into place (Fig_d).
4 BASKET ASSEMBLY: to facilitate basket assembly, pull the
tab outwards and lift as shown in the figure (fig_a).
Slip the basket flap into the slot along the front bar of
the chassis (Fig_b).
5 Fasten the basket eyelets to the buttons on each side
of the frame.
6 To complete the basket attachment procedure for the
front part, you are required to insert the supplied tie
(fig_1) as follows:
position it between the basket and buttons, as shown
(fig_2) and use your finger to push downwards, so as
to complete the attachment procedure (fig_3).
Repeat the same procedure for the other side of the
basket.
7 Attaching the rear part of the basket.
Remove the card from the rear bar.
Fasten the upper basket eyelet to the button on each
side of the frame (Fig_e).
Fasten the basket's two lower eyelets to the two
buttons on the rear bar of the frame (Fig_f).
8 Basket fastened correctly (fig_g).
Lastly, re-position the footrest, pressing inward with your
hand as shown in the figure (fig_h).
It is possible to increase the basket capacity by pulling the
tab outwards (fig_i).
WARNING! If you do not hook the basket on correctly,
as shown, the basket will be unable to support the
weight of loads placed in it.
9 HOOD: Fasten the back of the hood with the Velcro strip
(fig_a), insert the hood fasteners into their slots (fig_b),
secure to the buttons inside the handlebar with the rubber
band (fig_c) and button the hood to the side of the frame
(fig_d).
10 Supplied with two parasol sections. To open, pull forwards
(fig_a).
The hood includes a loop to be used to hang your child's
favourite toy (fig_b). You can detach the Velcro, roll up the
back of the hood and fasten it at the top with the rubber
band, so as to allow for greater ventilation when using with
the backrest down (fig_c).
11 FRONT BAR: insert the front bar as per the sequence shown
in the figure.
12 It can be adjusted into 2 positions:
POSITION 1: to use
- 18 -