Honeywell MORLEY-IAS DX CONNEXION Serie Manual De Usuario página 3

User Guide for the
Fire Alarm Control Panels
User Levels
- The DX Connexion Series Fire Alarm Control Panels have three available user levels for panel operation and control. At all
three levels, the LCD is the primary status indicator of the panel; detailed information on alarms and faults is presented
together with appropriate panel status LED indications.
- User Level 1: the user control keys are inhibited restricting the front panel function to indication only. The Mute Buzzer and
Show Alarm Zones user function keys may be operable.
- User Level 2: the user control keys are active allowing control for Mute Buzzer, Silence/Resound, System Reset, Extend
Delay, Show Alarm Zones and Evacuate. User Level 2 also allows test and disable/enable functions to be performed. User
Level 2 is reached by entering a passcode from User Level 1 or turning the keyswitch, if fitted and configured for this function.
- User Level 3: allows full system configuration and programming. This level is for use by the installer/maintenance provider only.
- Consult the DX Connexion Series User Manual for detailed information on user levels and operation. To access Level 2,
press the key and, using the numeric keypad, press '5' and enter the passcode at the screen prompt.
OK
DX Connexion Series Controls and Displays
Numeric Keypad (menu option selection keys)
0-9 Keys
For number entry. Also used
for alphabet entry during
programming and
configuration.
Key
Press to cancel a change or
return to a previous menu.
Key
C
Press to back-space when
correcting entries such as
passcodes.
System Status
LEDs
Fire Zone LEDs (optional)
Zones 1-40/1-80
Normal Condition
Green AC Power LED only is on.
Mains Power Failure
Supply Fault LED lights and
internal buzzer sounds intermittently.
Periodic Testing
Check that the panel indicates normal operation. If not, record the fault in the log book and report to the maintenance
Daily:
provider. Check any previously-reported faults have received attention.
Monthly: At least one call point or detector (from different zones each month) should be operated to test the fire panel and
any connected alarm/warning devices. Where permissable, any link to the fire brigade or remote centre should be
operated. If any faults exist, record these in the log book and report to the maintenance provider.
Series
Key Switch (optional)
LCD
Menu Navigation Keys
Press to confirm changes or select a menu option. Press
OK
and scroll through Level 1 display functions for fire, fault, disablement and test conditions.
Fire Alarm Condition
FIRE LED is on. Zone Fire LEDs (if
fitted) indicate the location of the
alarm. The internal buzzer sounds
continuously.
DX Connexion Series
User Guide
996-214-002-2
This document must be framed and mounted in view and adjacent to the
Fire Control Panel.
User Control Keys
Mute Buzzer
Press to silence the internal buzzer.
Silence/Resound
Press to silence the sounders.
Press again to re-activate.
System Reset
Press to cancel all alarm conditions and
reset the panel after cause of alarm has
been corrected.
Extend Delay
Press to acknowledge Stage 1 Delayed
Alarm. Stage 2 delay period starts.
Show Alarm Zones
Displays fire alarm information. If there is
more than one zone in alarm, scrolls
through these zones.
Evacuate
Press to turn on ALL Sounder Outputs,
i.e. evacuate building manually.
Fault Condition
The LCD displays fault information.
General Fault LED and system LEDs
indicate the type of fault. The internal
buzzer sounds intermittently.
© MORLEY-IAS by Honeywell 2011. All rights
reserved.
® The MORLEY-IAS Logo is a registered trade-
mark.
MORLEY-IAS Fire Systems by Honeywell, Charles
Avenue, Burgess Hill, West Sussex RH15 9UF. UK.
www.morley-ias.co.uk
, , and keys to select