General Safety Precautions; Rules For Safe Operation; Electrical Safety; Personal Safety - McCulloch Li 40HT Manual De Instrucciones

Your hedge trimmer has been engineered and
manufactured to McCulloch's high standard for
dependability, ease of operation, and operator safety.
When properly cared for, it will give you years of
rugged, trouble-free performance.

RULES FOR SAFE OPERATION

WARNING! Read all safety warnings
!
and all instructions. Failure to follow
the warnings and instructions may
result in electric shock, fire and/or
serious injury.
INTENDED USE
This hedge trimmer is intended for cutting and trimming
hedges and bushes in domestic use. It is not intended
to be used for cutting above shoulder level.
„ Save all warnings and instructions for future
reference. The term "power tool" in the warnings
refers to your battery-operated (cordless) power
tool.
WORK AREA SAFETY
„ Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
„ Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
„ Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.

ELECTRICAL SAFETY

„ Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
„ Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
„ If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.

PERSONAL SAFETY

„ Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
„ Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, gloves, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
„ Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.

GENERAL SAFETY PRECAUTIONS

Carrying power tools with your finger on the switch
or energizing power tools that have the switch on
invites accidents.
„ Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
„ Do not over-reach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
„ Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
„ If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
POWER TOOL USE AND CARE
„ Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was designed.
„ Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
„ Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
„ Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
„ Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
„ Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
„ Disconnect the battery pack from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
BATTERY TOOL USE AND CARE
„ Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites
accidents.
„ Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
English (Original Language) - 5