Connecting The Device; Connecting The Power; Control Panel View - STAMOS S-MULTI 195 IGBT Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27

3.3 CONNECTING THE DEVICE

3.3.1 CONNECTING THE POWER

The power connection must be performed by a qualified person. In addition, a suitably qualified person
should check whether the earthing and electrical system are in accordance with the safety regulations
and if it works properly.
The device must be placed near the work station.
The connection of excessively long conduits to the machine must be avoided.
One-phase welders should be connected to the socket fitted with an earthing prong.
Welders powered from a 3-Phase network are delivered without a plug, the plug must be obtained
independently and installation should be assigned to a qualified person.
PLEASE NOTE! THE DEVICE MAY ONLY BE USED UPON CONNECTION TO AN
INSTALLMENT WITH A PROPERLY FUNCTIONING FUSE
4. OPERATION
S-MULTI 195 IGBT (2162) WELDING MACHINE
Machine description:
Front view:
1 2 3
4
5
6
7
8
No.
Function and description:
1.
Welding current display
2.
Welding voltage display
3.
VRD indicator
Safety function – only for MMA welding: This function allows to reduce the idling voltage to a
user-safe value when the device is ready for welding. After commencing welding, the idling voltage
automatically grows to the nominal value, and after finishing welding it drops back to the safe
value again.
EN
Rear view:
9
10
11
12
Inside view:
14
Rev. 20.03.2017
4.
Knob used to adjust filler wire feed rate and to adjust welding current.
5.
Knob used to adjust downslope current / voltage.
6.
„+" lead output
7.
MIG connector
8.
TIG control connector / SpoolGun feeder power connector
9.
2T/4T SWITCH:
2T – press this button on the burner to start the metal welding/cutting process, release this
button to end this process.
4T – press this button on the burner to start the metal welding/cutting process, releasing this
button does not end this process. Press and release this button again to end the metal welding-
cutting process
10.
Operation mode selection knob: MIG / TIG / MMA / SYNERGIC SET MIG Function
11.
„-" lead output
12.
Polarisation change pin:
Connected to the positive pole – MIG welding
Connected to the negative pole – FLUX welding
13.
On/off switch
14.
Power cable
13
15.
Gas connector
14
16.
Operation mode switch: built-in feeder / SpoolGun
15
17.
Filler wire feed – once this button is pressed the welding machine begins feeding filler wire. Filler
wire will continue to be fed until the button is released. It is used to control the feed rate, or to
feed filler wire after a spool was changed.
18.
Filler wire guide

CONTROL PANEL VIEW:

2
3
16
17
No. MMA
18
1.
Arc Force display
2.
Welding current
display
3.
Welding current
adjustment knob
4.
Arc Force adjustment
knob
5.
Welding mode
selection: MMA
6.
Not applicable
Rev. 20.03.2017
EN
6
1
5
4
TIG
MIG
Downslope current
Voltage display
Welding current display
Filler wire feed rate / welding current
display
Welding current
Filler wire feed rate adjustment knob
adjustment knob
Downslope current
Voltage adjustment knob
adjustment knob
TIG welding
MIG welding
mode selection
mode selection
2T / 4T switch
15
SYNERGIC SET
MIG Function
SYNERGIC SET
MIG welding mode
selection

Publicidad

Tabla de contenido
loading

Tabla de contenido