Mitsubishi Electric PLA-A12AA Manual De Instrucciones página 4

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2. Parts Names
Wired
Remote-Controller
I
Display Section
I
Orpurposes of this explanation,_
II parts of the display are shown I
lit. Duringactual operation, only I
e relevant items will be lit.
/
/
Identifies the current operation
Shows the operating mode, etc.
* Multilanguage
display
is sup-
ported.
"Centrally
Controlled"
indicator
Indicates that operation of the re-
mote controller
has been prohib-
ited by a master controller.
"Timer is Off" indicator
Indicates that the timer is off.
Temperature
Setting
Shows the target temperature.
Day-of-Week
Shows the current day of the week.
Time/Timer
Display
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, shows the time
remaining.
_,
MITSUBISHI ELEITRIC
TiME
SUN
MON
TUE..WED
THU
FRI SAT I
_
_[_]
TIMER
El
L/
" El
L
I Hr
ON
I
AFTER
I II
I " I II
I AFTER
OFF
JOl
I
1
I
Up/Down
Air Direction
indica-
Room Temperature
display
tor
Shows the room temperature. The room
The indicator '% shows the direc-
temperature
display
range is 8-39°C.
tion of the outcoming
airflow.
The display flashes if the temperature
is less than 8 °C or 39 °C or more.
"One
Hour Only"
indicator
Displayed
if the airflow
is set to
Louver
display
weakand downward during COOL
Indicates the action of the swing louver.
or DRY mode. (Operation
varies
Does not appear if the louver is station-
according to model.)
ary.
The indicator
goes off after one
hour, at which time the airflow di-
(_) (Power
On indicator)
rection also changes.
Indicates that the power is on.
m
"Sensor"
indication
Displayed when the remote controller
sensor is used.
"Locked"
indicator
Indicates
that remote controller
but-
tons have been locked.
"Clean
The Filter"
indicator
Comes on when it is time to clean the
filter.
Timer
indicators
The indicator
comes
on if the corre-
sponding
timer is set.
Fan Speed
indicator
Shows the selected fan speed.
Ventilation
indicator
Appears
when the unit is running in
Ventilation
mode.
Operation Section
_Set Temperature
buttons
Down
up
I Timer
Menu button
(Monitor/Set
button)
Mode button (Return button)
I
I Set Time buttons
Back
(_
Ahead
I
imer On/Off button
_}_
(Set Day button)
Opening the
door.
MITSUBISHI
ELECTRIC
J
@ 0 q/OFF
o
--
__ TEMP.
(2D
i
I_--!_ 00638_
C)MENU
_ON/OFF
FILTER
_.
ONSETDAYI I :-_=_
3_:.lJ
CHECK
TEST
Built-in temperature
sensor
ON/OFF button
)eed button
Filter _ button
(<Enter> button)
%
Test Run button J
[__
heck button (Clear button)
Airflow Up/Down button
;
_
(L?VorpbeUatti°nnbutt°n)1
(_
To preceding
operation
number.
--I
(Vz_nt_)_P:°ntib°Lttbuntton)1
(_To
next operation
number.
Note:
• "PLEASE WAIT" message
This message is displayed for approximately
3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure,
• "NOT AVAILABLE" message
This message is displayed if a button is pressed to operate a function that the indoor unit does not have,
If a single remote controller is used to simultaneously
operate multiple indoor units that are different models, this message will not be displayed if
any of the indoor units is equipped with the function,
4

Publicidad

Tabla de contenido
loading

Tabla de contenido