English; Start-Up Guide - Konrow CHIPO 3 Guia Del Usuario

English

1. Inserting a SIM card
Chipo3 is a mobile phone with dual SIM card which enables you to
use two lines on the same mobile. Your Chipo3 has two standard
SIM ports. To insert the SIM card(s):
• Switch off the phone and remove the rear cover and battery.
• Insert the SIM card correctly into the relevant card slots (see
figure below).
• Then replace the battery and cover.
2. Inserting a Micro SD
It is possible to increase the internal memory of the Chipo3 device
with a MicroSD card (maximum 32GB MicroSD card).
• Switch off the phone and remove the rear cover and battery.
• Insert the memory card into the relevant slot.
• Then replace the battery and cover.
CAUTION: Inserting or removing a SIM card or a MicroSD card
requires the mobile to be completely switched off.
3. Installing and charging the battery
Installing the battery:
• Remove the rear cover of your mobile.
• Insert the battery ensuring that the image shown here is facing you.
• Replace the rear cover of the mobile.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Model : Chipo3
Li-ion 3.7V /800 mAh.
To replace the battery, please enquire with the after-sales service of your dealer. Dispose of
used batteries according to the instructions.
Charging the battery:
• To charge the battery, connect the USB cable (supplied) to the USB port of your mobile
then connect the mains adaptor to a power outlet.
• The battery charge icon illuminates during charging and indicates the charge status.
• When the battery is fully charged, you can disconnect the USB cable from the device
then from the power outlet.
IMPORTANT:
• The mobile is only recharged via its USB port.
• Ensure your mobile is fully discharged before charging it for the first time.
• The battery must be charged for at least 5 to 8 hours when first charged.
Note: You can use the device when it is being charged. In this case, the battery may take
longer to charge fully.
Safety information for charging the battery:
• To recharge the battery, only use the mains adaptor supplied with your device. Do not use any
other power supply or electrical device. The power outlet to which the device is connected must
be near the equipment and must always be easily accessible.
• Always wait at least 5 seconds after switching off the device before restarting it. Switching the
device off and then back on again immediately may damage the electrical circuits.
• Do not disassemble the battery. Do not dispose of batteries in fire or water. Do not charge the
12
battery if the room temperature exceeds 45°C.
• For all repairs or to replace the battery, consult a qualified
technician.
• The lifetime of the battery depends largely on how you use
it. Do not expose the battery to temperatures less than 0°C or
greater than 60°C. Its performance may be altered.
• Significant electromagnetic interference or electrostatic
discharge may cause malfunction or loss of data. If the
device is not working properly, restart the mobile or
unplug the mains adaptor from the power outlet then
plug it in again.
4. Switching the mobile on and off
To switch the mobile on, press the On/Off button located on the
side of the mobile for 3 seconds.
If the mobile is switched on, press for less than a second on the
button to put the device into standby mode.
To switch off the mobile, press the On/Off button for 3 seconds
until a menu appears, then touch the Off button and confirm.
5. Locking/unlocking SIM cards
Your Chipo3 is a dual SIM mobile. It enables you to phone using two lines from the same
device. There are two SIM card slots.
• When you start up your phone, the latter invites you to enter the PIN codes of your two
SIM cards in succession (SIM1 then SIM 2).
• The ''emergency call'' function enables you to call an emergency number without
entering the PIN code.
6. Locking/unlocking the keypad
To lock the screen:
press the lock button then the * button
To unlock the screen:
press the lock button then the * button
You can configure the screen lock by adding a
password or pattern to be replicated when unlocking
your mobile.
CAUTION: Forgetting your screen lock password, PIN
code or pattern permanently blocks your mobile.
If this is forgotten or lost, the product warranty will not
cover such an oversight. Even a "reset"
cannot solve the problem. As a precaution, take a note
of your password or pattern.
PASSWORD: _________________

Start-up guide

Lock/
Unlock
keys
13
EN