Installation Instructions - Cardin SL 324EBSB Manual De Instrucciones

- check the gate components, replace any worn or damaged parts and then
lubricate them.
N
O
not inhibit the gate's sliding action.
- check that a mechanical travel limit Q (absolutely necessary) has been
fitted in the opening direction and that it corresponds to the maximum travel
P
The travel limit must guarantee anti-derailment and gate stability.
Warning! It is the installer's responsibility to check all critical danger
points, to take action and to install any devices needed to guarantee
the safety of all people using the gate (risk analysis).

INSTALLATION INSTRUCTIONS

Important: The geared motor can be positioned either to the left or to the
right of the passageway.
INSTRUCTIONS FOR POSITIONING THE UNIT
the correct position has been chosen proceed as follows:
Anchoring the unit (fig. 4, 5, 6)
Important! Check the exact anchoring position with respect to the alignment
of the sliding gate.
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
be installed.
50 mm and then tighten down using the supplied M12 nuts.
with a depth of 350 mm (the base should protrude by about 25 mm to avoid
damage by pools of water building up under the appliance).
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
C
is perfectly level;
- the four protruding (50 mm) threaded bolts are perpendicular to the base
plate;
- the surface area of the base plate is clean and free of cement residue.
4
SCALA: 1:2
Drawing number :
DI0237
Product Code : SL1524M
Draft : P.J.Heath Date : 30-01-2002
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
A
B
SCALA: 1:2
Drawing number :
Product Code :
Draft :
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/40
B
C
2
Description : Prodotti Technocity
CONTROPIASTRA SL1524M
If the runner guide already exists the cement base should be extended
to take in part of the runner guide foundation.
This will stop the two foundations from giving way separately.
- Unscrew the four M12 nuts on the four threaded bolts (previously
used to block the anchor bolts) from the base of the anchor
plate. Then insert the four washers and allow them to rest on
the nuts.
- Position the geared motor over the four threaded bolts and
allow it to rest on the four washers.
- Fasten in to the base using the other
four washers and adjustment nuts
supplied with the kit, making sure
that the unit remains perfectly level
and stable.
- Adjust the height if the unit
using the four grub screws
already positioned on the
motor.
This will allow you to adjust
the height and position of
the motor later on.
All rights reserved. Unauthorised copying or use of the information contained in this do
Fitting the toothed rack
- release the geared motor (fig. 8), lay the first stretch of the toothed
rack on the pinion and fix it to the gate, then fasten down all the other
parts along the entire length of the gate.
- after having fastened the toothed rack, realign the pinion (play of 1
to 2 mm between the toothed runner and the pinion) using the grub
screws at the base of the geared motor.
This action will prevent the weight of the sliding gate from damaging
the unit when working.
6
2 mm
2
M 1
DI0406
SL1524
Date :
P.J.Heath 03-05-2005
A
1
3
4
SCALA: 1:2
Drawing number :
DI0240
Product Code : SL1524
15
Draft : P.J.Heath Date :
104,5
Description :
Prodotti Cardin
VISTA DI FIANCO SENZA
con plinto 350 mm
Description : Prodotti Technocity
VISTA DI FIANCO CON MOT
08-02-2002
5