Start-Up; Leds Check; Programming The Dips-Switch; Pre-Flashing - FAAC E391 Manual De Usuario

6 START-UP

6.1 LEDS CHECK

The following table shows that status of the LEDs in relation to
the status of the inputs (the closed at rest automated system
condition is shown in bold).
Check the status of the signalling LEDs as per table below:
Tab.1 – Operation of inputs status LEDs
LED ON (closed contact)
STOP Command disabled
OPEN A Command enabled
OPEN B Command enabled
BUS

6.2 PROGRAMMING THE DIPS-SWITCH

The following tables show the settings of the DS1 dip-switch for
programming force, pre-flashing and reversing stroke.
Tab. 2 - DS1 programming (default settings in bold)
DS1 DS2 DS3 DS4
ON ON
ON OFF
OFF ON
OFF OFF
ON
OFF
ON
OFF
If you connect an electric lock to terminal J4,
position DS4 to ON to enable the reversing stro-
ke (before opening, the motors thrust to close,
thus facilitating the electric lock to uncouple).
By setting dip-switch DS3 on ON, a special By setting dip-switch DS3 on ON, a special
windproof function is activated that enables the
gate operation even if strong wind is present.

6.3 PRE-FLASHING

The pre-flashing function can be activated and disabled (fol-
lowing an OPEN command, the unit activates the flashing lamp
for 3 seconds before it starts the movement). Procedure:
1. Press LOGIC key (SW3) for at least 5 secs. to ACTIVATE
pre-flashing.
2. Press SPEED key (SW2) for at least 5 secs. to DESACTIVATE
pre-flashing.
In both cases check if the LED of the pressed key
changes its status: in such cases it means that
the function of the key and not the pre-flashing
was changed.
OFF (open contact)
Command enabled
Command disabled
Command disabled
See par. 7.2
Description
HIGH FORCE
MEDIUM - HIGH FORCE
MEDIUM - LOW FORCE
LOW FORCE
ANTI-WIND ON
ANTI-WIND OFF
REVERSING STROKE ON
REVERSING STROKE OFF

6.4 TIME - SETUP LEARNING

Before any manoeuvre is executed, a SETUP
cycle must first be run.
During SETUP do not interrupt the photocells
because their interruption causes the immedi-
ate stop of the leaves. To end the procedure,
repeat SETUP from the beginning.
When the board is powered up and a SETUP cycle has never
been executed, LEDs LD4 and LD5 begin to flash slowly to signal
that a SETUP cycle must be executed.
There are two possible types of SETUP: AUTOMATIC and
MANUAL
6.4.1

AUTOMATIC SET-UP

To execute an AUTOMATIC SETUP , follow the procedure below:
1. Take the leaves to mid-point.
2. Hold down the SETUP (SW1) push-button until the 2 adjacent
LEDs (LD4 and LD5) light up on steady beam.
3. Release the SETUP push-button, LEDs LD4 and LD5 begin
to flash rapidly.
4. Leaf 2 (if present) starts the closing movement, stopping
when it reaches the closing mechanical stop.
5. Leaf 1 starts the closing movement, stopping when it
reaches the closing mechanical stop.
6. Leaf 1 starts the opening movement.
7. Leaf 2 (if present) starts the opening movement after a
fixed delay at opening.
8. Leaves 1 and 2 (if present) stop when they reach the
opening mechanical stop.
9. Wait for LEDs LD4 and LD5 to go OFF, which means that the
SETUP procedure has finished.
10. Give an OPEN pulse to close the gate.
When the SETUP procedure has been started,
if the leaves at point 4 and 5 open instead of
closing, the motor power supply cables must
be changed over.
When using the AUTOMATIC SETUP , the slow
down spaces, the leaf opening and closing
delays, and the pause time (30 sec., with A
logic), are all preset by the board and cannot
be modified.
6.4.2

MANUAL SET-UP

To execute a MANUAL SETUP , follow the procedure below:
1. Take the leaves to mid-point.
2. Hold down the SETUP (SW1) push-button until the leaves
start to move.
3. Release the SETUP push-button, LEDs LD4 and LD5 begin
to flash rapidly
4. Leaf 2 (if present) starts the closing movement, stopping
when it reaches the closing mechanical stop
5. Leaf 1 starts the closing movement, stopping when it rea-
ches the closing mechanical stop
6. Leaf 1 starts the opening movement.
7. Leaf 2 (if present) starts the opening movement after a
fixed delay at opening.
8. Leaves 1 and 2 (if present) stop when they reach the ope-
ning mechanical stop.
9. If LOW force was set, wait for about 5 sec checking if the
flashing lamp goes OFF.
4