Description - Hilti WSR 900-PE Manual De Instrucciones

Location of identification data on the tool
The type designation and serial number can be found on
the rating plate on the tool. Make a note of this data in
your operating instructions and always refer to it when
making an enquiry to your Hilti representative or service
department.
en

2. Description

2.1 Use of the WSR 900-PE as directed
Typical working environments include rescue services,
●
public authorities, farming and forestry, general con-
struction, renovation and conversion work, metal con-
struction, plumbing / heating / air-conditioning instal-
lation trades, in workshops and on construction sites.
The tool may be used for cutting wood, wood-like
●
materials, metals and plastics.
The tool must be used in a dry environment.
●
The tool may be powered only by an electric supply
●
voltage in compliance with the information given on
the type plate.
The tool is designed for two-handed operation.
●
Use only the blades and accessories listed in the oper-
●
ating instructions.
Do not use the tool to cut bricks, concrete, cellular
●
concrete, natural stone or tiles.
Do not use the tool in a damp environment.
●
Do not use the tool in environments where there is a
●
risk of explosion.
Do not use the tool to cut pipes that still contain liq-
●
uids.
Do not cut into unknown materials.
●
Use the tool within its intended cutting performance
●
range and with suitable blades (do not use blades of
the wrong size or reciprocating saw blades not equipped
with a 1 / " connection end).
2
Cutting materials containing asbestos is not permis-
●
sible.
Changes or modifications to the tool are not permissible.
●
To avoid the risk of injury, use only original Hilti acces-
●
sories and additional equipment.
Observe the information printed in the operating instruc-
●
tions concerning operation, care and maintenance.
The tool is intended for professional use.
●
The tool may be operated, serviced and repaired only
●
by authorized, trained personnel. This personnel
must be informed of any special hazards that may
be encountered.
The tool and its ancillary equipment may present haz-
●
ards when used incorrectly by untrained personnel or
when used not as directed.
-WARNING-
Before cutting pipes, always first ensure that the pipes
14
Printed: 21.08.2013 | Doc-Nr: PUB / 5138031 / 000 / 01
Type:
Serial no.:
contain no liquids. Empty the pipes if necessary. The
tool is not water or moisture proof. Liquids running out
may cause a short circuit in the tool resulting in an elec-
tric shock being received. When cutting pipes, hold the
tool so that it is higher than the pipe being cut.
2.2 Use of the WSR 1250-PE / WSR 1400-PE as
directed
Typical working environments include general con-
●
struction, renovation and conversion work, metal con-
struction, plumbing / heating / air-conditioning instal-
lation trades, rescue services, public authorities,
farming and forestry, in workshops and on construc-
tion sites.
The tool may be used for cutting wood, wood-like
●
materials, metals, plastics, bricks, cellular concrete
and tiles.
The tool must be used in a dry environment.
●
The tool may be powered only by an electric supply
●
voltage in compliance with the information given on
the type plate.
The tool is designed for two-handed operation.
●
Use only the blades and accessories listed in the oper-
●
ating instructions.
Do not use the tool to cut concrete or natural stone.
●
Do not use the tool in a damp environment.
●
Do not use the tool in environments where there is a
●
risk of explosion.
Do not use the tool to cut pipes that still contain liq-
●
uids.
Do not cut into unknown materials.
●
Use the tool within its intended cutting performance
●
range and with suitable blades (do not use blades of
the wrong size or reciprocating saw blades not equipped
with a 1 / " connection end).
2
Cutting materials containing asbestos is not permis-
●
sible.
Changes or modifications to the tool are not permissible.
●
To avoid the risk of injury, use only original Hilti acces-
●
sories and additional equipment.
Observe the information printed in the operating instruc-
●
tions concerning operation, care and maintenance.
The tool is intended for professional use.
●
The tool may be operated, serviced and repaired only
●
by authorized, trained personnel. This personnel