Hitachi Koki D 6SH Instrucciones De Manejo página 4

English
PRECAUTIONS ON USING DRILL
1. When mounting the drill bit, insert it fully into the
drill chuck and completely tighten the drill chuck
with the chuck wrench.
If mounting is not done porperly, it is very dangerous
as the drill bit may slip or loosen during operation.
2. Do not wear gloves made of stuff liable to roll up
such as cotton, wool, cloth or string, etc.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-load speed
Steel
Capacity
Wood
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Chuck wrench ..............................................................1
(2) Stopper Ass'y ..............................................................1
(3) Hook ..........................................................................1
Standard accessories are subject to change without
notice.
APPLICATIONS
○ Drilling holes into various metals, lumbers and
plastics.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of suffi cient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting the drill bit
Fit the drill bit into the chuck and use the chuck
wrench to secure it, tightening the chuck by each of
the three holes in turn. (Fig. 3)
5. Selecting the appropriate drill bit
(1) When drilling holes in metals or plastics:
Use ordinary metalworking drill bits;
Applicable drill sizes range from 0.5 mm min. to
6.5 mm max.
(2) When drilling holes in lumber:
Use woodworking drill bits.
For small holes of 6.5 mm dia, or less, use
metalworking drill bits.
3
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
4. When placing the drill on the fl oor, make sure that
the drill has stopped completely.
5. Before drilling into a wall, fl oor or ceiling, thoroughly
confi rm that no items such as electric cables or
conduits are buried inside.
6. When working in high position, take care of
downword direction.
D6SH
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
240 W*
4500/min
6.5 mm
9 mm
0.9 kg
PRACTICAL HANDLING PROCEDURES
1. Pressure
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result
in a damaged drill bit, decreased drilling effi ciency
and/or shortened service life of the drill.
2. When drilling completely through the material
When the drill bit bores completely through the
material, careless handling often results in a broken,
drill bit or damage to the drill body itself due to the
sudden movement of the drill. Always be alert and
ready to release pushing force when drilling through
the material.
3. Switch operation:
By pulling the trigger switch and depressing the
stopper, the switch is held in the ON position for
continuous operation. To turn the drill OFF, pull the
trigger switch again and release.
4. Precautions on Boring
The drill may become overheated during operation;
however, it is suffi ciently operable. Do not cool the
drill bit in water or oil.
5. Using stopper assembly (Fig.1)
NOTE: The stopper rod can be fi xed on whichever
side of the housing.
Adjust the stopper rod to reach a required drilling
depth. To fi x it securely, use the stopper bolt.
6. Caution immediately after use
Immediately after use, if the Drill is still revolving
and it is placed on a location where considerable
ground chips and dust have accumulated, dust may
occasionally be absorbed into the Drill mechanism.
Always pay attention to this possibility.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch power OFF and disconnect the
plug from the receptacle during maintenance and
inspection.
D6SB
3000/min
6.5 mm
13 mm