Installation Instructions; Electrical Connections - Hoshizaki FM-481ALGE Manual De Instrucciones

Ocultar thumbs Ver también para FM-481ALGE:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
IMPORTANT
1. This booklet is an integral and essential
part of the product and should be kept and
preserved by the user. Please read carefully
the guidelines and warnings contained
herein as they are intended to provide
the user with essential information for the
continued safe use and maintenance of the
product. In addition, it provides GUIDANCE
ONLY to the user on the correct services
and site location of the icemaker. Please
preserve this booklet for any further
consultation that may be necessary.
2. This is a commercial icemaker, and should
be destined only to be used for the purpose
for which it has been expressly designed.
A n y o t h e r u s e s h o u l d b e c o n s i d e r e d
improper and therefore dangerous. The
manufacturer will not be held liable or
responsible for any damage caused by
improper, incorrect and unreasonable use.
I. INSTALLATION INSTRUCTIONS
WARNING
1. The installation must be carried out
by qualified personnel, in accordance
with current regulations, according to the
manufacturer's instructions.
2. Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear
of obstruction.
1. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor
use. Normal operating ambient temperature
should be within 5°C to 40°C. Normal
operating water temperature should be
within 5°C to 35°C. Operation of the
icemaker, for extended periods, outside
of these normal temperature ranges may
affect production capacity.
2. The icemaker should not be located next to
ovens, grills or other high heat producing
equipment.
3. The location should provide a firm and level
foundation for the equipment.
4. Allow 15 cm clearance at rear and sides
for proper air circulation and ease of
maintenance and/or service should they be
required. Allow 60 cm clearance on top to
allow for removal of the auger.
5. This appliance is not suitable for installation
in an area where a water jet could be used
and where dripping is not allowed.
6. D o n o t p l a c e a n y t h i n g o n t o p o f t h e
icemaker or in front of the louver.

2. ELECTRICAL CONNECTIONS

WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets
t h e n a t i o n a l a n d l o c a l e l e c t r i c a l c o d e
requirements. To prevent possible severe
electrical shock to individuals or extensive
damage to equipment, install a proper earth
wire to the icemaker. Disconnect the main
power supply before any maintenance, repairs
or cleaning is undertaken.
* T h i s a p p l i a n c e r e q u i r e s a s e p a r a t e 2 2 0 -
240VAC, 13A supply. The electrical supply must
be protected by a suitable circuit breaker.
* Usually an electrical permit and services of a
licensed electrician are required.
* If the supply cord and/or the plug should need to
be replaced, it should only be done by a qualified
service engineer.
* In accordance with the requirement of the IEC
standard, the maximum permissible system
impedance (Zmax) at the interface point of the
power supply to be connected with this icemaker
must be 0.2908+j0.18175 ohm. Determine
in consultation with the supply authority, if
necessary, that the icemaker is connected only to
a supply of 0.2908+j0.18175 ohm or less.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
1
ENGLISH

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Fm-481alge-n

Tabla de contenido