Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
bye&
S_on
_
_
_OV/ER p _r>_JC r s
H.
Detach
spray gun and nozzHe extension
from
hgh
pressure
hose. Detach
nozzHe extension
from
spray gun
and remove
o:fing
and screen
from
nozzHe extension.
Hush
the screen_ spray gun_ and adiustabHe
nozzHe
extension
with
dean
water
to dear
debris.
2.
If the screen
is damaged_ the o:fing
Halt contains
a
repHacement
inoHine fiker
screen
and an o:fing.
[f
undamaged_
reuse
screen.
3.
PHace the inoHine fJker
screen
into
the threaded
end of
the nozzHe extension.
Direction
does not matter.
Push
the screen
in with
the eraser
end of a penciH untiH it
rests
ilat at the bottom
of the opening.Take
care to
not bend
the screen.
4.
PHace the o°ring
into
the recess.
Push the o°ring
snugHy
against
the inoHine fiker
screen.
5.
AssembHe
the nozzHe extension
to the spray gun, as
described
earHier in this manual
Purge
Pump
of Air
and
To remove
air from
the
Dump,
follow
these
steps:
Set up the pressure
washer
as described
in "Preparing
Pressure
VVasher
For Use".
Connect
the
water
suppHy and
turn
water
on.
o PuHHthe
trigger
on the
spray
gun
and hoHd.
o When
the
water
suppHy is steady
and
constant_
engage
the
safety
Hatch.
To remove
contaminants
from
the
pump,
follow
these
stepst
o Set up the pressure
washer
as described
in "Preparing
PressureWasher For Use". Connect the water suppHy
and turn
water
on.
o Start the engine according to instructionsin"To Start
Your Pressure VVasher".
° Remove
nozzle
extension
from
spray
gun.
o Squeeze
the
trigger
on the
spray
gun and
hoHd.
o When
the
water
suppHy is steady
and
constant,
engage
the
safety
Hatch and
attach
the
nozzHe
extension.
Nozzle
Maintenance
A puHsing sensation
fek whiHe squeezing
the spray gun
trigger
may be caused
by excessive
pump
pressure.The
principa[
cause of excessive
pump
pressure
is a nozzHe
c[ogged
or restricted
with
foreign
materiak
such as dirt,
etc.To
correct
the
problem,
immediately
clean
the
nozzle
using the tooHs incHuded
with
your
pressure
washer
and
foHHow these
instructions:
I.
Shut
off the
engine
and
turn
off the water
supply.
2.
Detach
the
nozzHe
extension
from
the
spray
gun.Twist
the
nozzHe
c[ockwise
to the
stream
position.
Using
the
suppHied
2ram
(5/64)
aHHen wrench,
remove
the
nozzHe
from
the
end
of the
nozzHe
extension
(Figure
21).
3.
Remove the inoline filter from the other
end of the
nozzHe extension.
4.
Use the wire incHuded in the kit (or a smaHHpaper chip)
to free any foreign materia[
dogging or restricting
the
nozzHe (Figure 2H).
5.
Using a garden
hose, remove
additionaH debris
by bacH<
flushing water
through
the nozzHe extension
(Figure 22). BacH< flush between
30 to 60 seconds.Turn
the adiustabHe nozzHe extension
to stream
spray and
move the nozzHe from How to high whiHe flushing.
6.
Reinstall
the
nozzle and
in4ine filter
into the
nozzle
extension.
Do Not
overtighten
the nozzle
with
the
allen wrench.
7.
Reconnect
the nozzle
extension
to the spray gun.
8.
Reconnect
the water
supply,
turn
on the
water,
and
start
the
engine.
13
Publicidad
Tabla de contenido
