DeWalt DW077 Manual De Instrucciones página 38

Ocultar thumbs Ver también para DW077:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 48
E N G L I S H
Safety instructions
When using power tools, always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and
personal injury.
Read all of this manual carefully before operating
the tool. Also refer to the manual of any power
tool that will be used with this tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose power tools to humidity.
Keep work area well lit. Do not use power tools
in the presence of flammable liquids or gases.
3 Guard against electric shock
Prevent body contact with earthed surfaces
(e.g. pipes, radiators, cookers and refrigerators).
For use under extreme conditions (e.g. high
humidity, when metal swarf is being produced,
etc.) electric safety can be improved by inserting
an isolating transformer or a (FI) earth-leakage
circuit-breaker.
4 Keep children away
Do not let children come into contact with the
tool or extension cord. Supervision is required for
those under 16 years of age.
5 Use appropriate tool
The intended use is described in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which it
was intended.
Warning! The use of any accessory or attachment
or performance of any operation with this tool,
other than those recommended in this instruction
manual may present a risk of personal injury.
6 Maintain tools with care
Keep the tools in good condition and clean for
better and safer performance. Follow the
instructions for maintenance and changing
accessories. Inspect the tool cords at regular
intervals and, if damaged, have them repaired by
an authorized D
WALT repair agent. Keep all
E
controls dry, clean and free from oil and grease.
38
7 Store idle tools
When not in use, power tools must be stored in a
dry place and locked up securely, out of reach of
children.
8 Check for damaged parts
Before using the tool, carefully check it for damage
to ensure that it will operate properly and perform
its intended function. Check for misalignment
and seizure of moving parts, breakage of parts
and any other conditions that may affect its
operation. Have damaged guards or other
defective parts repaired or replaced as instructed.
Do not use the tool if the switch is defective.
Have the switch replaced by an authorized
D
WALT repair agent.
E
9 Remove the battery pack
Remove the battery pack when not in use,
before servicing and when changing accessories.
10 Have your tool repaired by an authorized
D
WALT repair agent
E
This power tool is in accordance with the relevant
safety regulations. To avoid danger, electric
appliances must only be repaired by qualified
technicians.
Additional safety instructions for lasers
• This laser complies with class 3R according to
DIN EN 60825-1:2001-11 (max 5 mW, 600-680
nm). Do not replace a laser diode with a different
type. If damaged, have the laser repaired by an
authorised repair agent.
Only qualified and trained persons are allowed to
install, adjust and operate the laser equipment.
Areas in wich class 3R lasers are used have to be
posted with an appropriate laser warning sign.
• Do not use the laser for any purpose other than
projecting laser lines.
• Before first use, check that the safety warnings
on the label have been formulated in your
language. Do not use the tool if it does not carry
the warnings in your language!
• Do not remove any of the warning labels from the
tool.
• Do not let children come in contact with the laser.
As the beam of a class 3R laser provides high
visibility over longer distances, the potential risk of
damage to the eye remains unchanged within the
radius of application.

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido