Scope Of Delivery (Fig. 1A - 1F); User Manual; Product Description; Intended Use - Invacare Aquatec 90000 Manual Del Usuario

Aquatec® 90000
Additional Label (Fig. 11)
Product designation
A
Product must be positioned centrally on the
B
toilet bowl. (See Chapter 10)
Never use corrosive fluids or abrasive agents for
C
cleaning. (See Chapter 11)
Please sit down on the toilet.
D
Maximum user weight
E
F Maximum cleaning time / temperature. (See
Chapter 11)
Sitting height a, b, c. (Depending on purchased
G
model)
The additional label is attached to underside of the lid
7 Scope of Delivery (Fig. 1a – 1f)
2 cm, with and without Armrest (Fig. 1a, 1b)
• Corpus, 2 cm
• Lid
• Base incl. 2x clips
• Screw (2x)
• Plastic nut (2x)
• Plug (2x) (for version without armrest)
• Armrest (2x), (for version with armrest)
•

User manual

6 cm, with and without Armrest (Fig. 1c, 1d)
• Corpus, 6 cm
• Lid
• Base incl. 2x clips
• Screw (2x)
• Plastic nut (2x)
• Height adapter
• Plug (2x) (for version without armrest)
• Armrest (2x), (for version with armrest)
• User manual
10 cm, with and without Armrest (Fig. 1e, 1f)
• Corpus, 10 cm
• Lid
• Base incl. 2x clips
• Screw (2x)
• Plastic nut (2x)
• Height adapter (2x)
• Plug (2x) (for version without armrest)
• Armrest (2x), (for version with armrest)
• User manual

8 Product Description

Aquatec® 90000 is a toilet seat raiser that elevates the
seating height on toilets for a better seating position. It is
available in three different heights: 2 cm, 6 cm, 10 cm. It
can be used with our without armrests providing support for
sitting down or standing up. It is fixed with a screws system
at the rear of the toilet bowl.

9 Intended Use

This product is intended to be used as an aid for self-hygiene
care and toilet purposes by users who have limited function
in their legs. The seating height on the toilet is increased by
the product. It provides additional support for sitting down
or standing up from a toilet seat by foldable armrests and is
installed on standard toilet bowls.
4
Indication
Restricted or limited mobility (e.g.: legs and/or hips) or
having balance issues to stand up or walk due to transitional
or permanent disabilities.
There are no contraindications known when using the
product as intended.
The maximum user weight is 150 kg.
10 Setup (Fig. 2a – 8)
CAUTION!
Risk of Pinching
– Take care during assembly.
Installing the Toilet Seat Raiser (Fig. 2a – 8)
1. Slide the screws in the designated slot in the base on
both sides. Place the base and the height adapter(s) (if
applicable) on your toilet as shown on the image. (See
table) Tighten the plastic nut.
Height 2 cm Fig. 2a
Height 6 cm Fig. 2b
Fig. 2c
Height 10 cm
2. Place the corpus by holding it upright and fixing it to
the base. (Fig. 3)
3. Loosen the plastic nuts, align the toilet seat raiser
centrally to your toilet. Close the plastic nuts. (Fig. 4)
4. If your product is without armrests install the plugs on
both sides. (Fig. 5)
5. Clip on the lid. (Fig. 8)
To dismount the toilet seat raiser reverse step 2 and
1.
Installing the Armrests (if applicable) (Fig. 6, 7)
1. Open the red clip by releasing the upper end of the clip
C and then the pin B of the red clip A. (Fig. 7) Then
install the armrests and close the red clip. (Fig. 6)
Ensure that the red clips A engage at two points:
first the pin B and then the upper end of the clip
C. (Fig. 7)
To disassemble the armrests, first release the upper
end of the clip C and then the pin B.
11 Maintenance
11.1 General Maintenance Information
This product is maintenance-free, provided that the cleaning
and disinfection instructions are adhered to.
11.2 Cleaning and Disinfection
General Safety Information
CAUTION!
Risk of Contamination
– Take precautions for yourself and use
appropriate protective equipment.
1470052-D