Pictograms; Composition Of Supply; Functions And Description - Tractel PROMAST Manual De Empleo Y De Mantenimiento

2.2. Pictograms

DANGER: Placed at the beginning of a line, designates instructions intended to prevent fatal, serious, light injuries and damage
to the environment.
IMPORTANT: Placed at the beginning of a line, designates instructions intended to prevent failure or damage of equipment,
GB
NOTE: Placed at the beginning of the line, designates instructions intended to ensure the efficiency or comfort of an installation,
a method of use, or a maintenance operation.
You must read the manual.
ENTER INFORMATION ON CONTROL SHEET: Enter the information on the detachable control sheet located on the central

3 - Composition of supply

• One bag containing this manual, the HT harness, and the compliance certificate.
4 - Function and description
• The HT harnesses are fall arrest equipment compliant with standard EN 361. These harnesses can be equipped with an EN 358 work
position holding belt and an EN 813 thigh strap assembly equipped with suspension point.
• The HT harnesses are body harnessing systems designed to stop a fall; they are built to receive fall arrest systems, belay lanyards and
work position holding lanyards: see figure 7.
• A fall arrest harness is the sole body harnessing system which can be used in a fall arrest system.
• Anchorage points available according to type of harness:
Type of harness
54
55
56
Promast
Secours
Electra
Transport
Greentool
Easyclimb
• Use of HT harnesses according to anchorage equipment:
• Back anchorage point: This point is designed to receive a fall arrest system or a restraint lanyard.
• Chest anchorage point: This point is intended to receive a fall arrest system or a restraint lanyard. It is recommended for climbing
• Belt side anchorage points: These are intended to receive work position holding lanyards.
DANGER: In a work position holding system, the lanyard must maintain taut and free movement must be limited to
0.6 m max.
• Belly anchorage point: This point is intended to receive accessories for movements along ropes, such as ascenders and
DANGER: Only the anchorage points marked "A" or "A/2" when connected together with another point marked "A/2" can be
used for connection to a fall arrest system. Connection to any other point is dangerous and prohibited.
• The Easyclimb harness has a thoracic anchor point, especially designed to be connected to a rail mounted fall arrester for ladders.
The thoracic anchor point has the specificity of moving in the event of a fall, by means of seams ripping apart. This innovation is
patented. It is especially positioned for this purpose, and does not hinder the operator when climbing or descending.
• The Greentool harness is a transport harness equipped with a saddle to improve user comfort when working in suspended positions.
• The saddle is a comfort component for work in suspended positions. It must be associated to a fall arrest harness and a fall arrest system
as a mandatory requirement.
• The saddle is equipped with points for fastening small tools and accessories.
Elastrac unit option: The HT harnesses can be equipped with two Elastrac
™
Do not use the harnesses for any application other than for height fall protection: use of the harnesses for recreational or sporting
purposes is prohibited.
18
but not directly placing the life or health of the operator in danger, or that or other persons, and/or not likely to cause
damage to the environment.
Back
1
1
1
1
1
1
1
1
1
on a ladder or working on a roof.
descenders.
back. These units are designed to provide an elasticity of 4 cm on the webbing on each strap.
page of this manual.
Anchorage points
Fall arrest
Sternal Thoracic
0 2
1 0
1 2
1 0
1 0
1 0
1 0
1 0
1 2
units mounted on the harness shoulder straps on the user's
™
Work position holding Suspension
Side
0
0
0
1
1
1
1
1
1
Belly
0
0
0
1
1
0
1
1
0