General Safety Rules - REMS Blitz Instrucciones De Uso

deu
6. Hersteller-Garantie
Die Garantiezeit beträgt 12 Monate nach Übergabe des Neuproduktes
an den Erstverwender, höchstens jedoch 24 Monate nach Auslieferung
an den Händler. Der Zeitpunkt der Übergabe ist durch die Einsendung
der Original-Kaufunterlagen nachzuweisen, welche die Angaben des
Kaufdatums und der Produktbezeichnung enthalten müssen. Alle in-
nerhalb der Garantiezeit auftretenden Funktionsfehler, die nachweisbar
auf Fertigungs- oder Materialfehler zurückzuführen sind, werden ko-
stenlos beseitigt. Durch die Mängelbeseitigung wird die Garantiezeit für
das Produkt weder verlängert noch erneuert. Schäden, die auf natürli-
che Abnutzung, unsachgemäße Behandlung oder Missbrauch, Miss-
achtung von Betriebsvorschriften, ungeeignete Betriebsmittel, über-
mäßige Beanspruchung, zweckfremde Verwendung, eigene oder frem-
de Eingriffe oder andere Gründe, die REMS nicht zu vertreten hat,
zurückzuführen sind, sind von der Garantie ausgeschlossen.
Garantieleistungen dürfen nur von einer autorisierten REMS Vertrags-
Kundendienstwerkstatt erbracht werden. Beanstandungen werden nur
anerkannt, wenn das Produkt ohne vorherige Eingriffe in unzerlegtem
Zustand einer autorisierten REMS Vertrags-Kundendienstwerkstatt ein-
gereicht wird. Ersetzte Produkte und Teile gehen in das Eigentum von
REMS über.
Die Kosten für die Hin- und Rückfracht trägt der Verwender.
Die gesetzlichen Rechte des Verwenders, insbesondere seine Mängel-
ansprüche gegenüber dem Händler, bleiben unberührt. Diese Herstel-
ler-Garantie gilt nur für Neuprodukte, welche in der Europäischen Union,
in Norwegen oder in der Schweiz gekauft werden.
7. REMS Vertrags-Kundendienstwerkstätten
Firmeneigene Fachwerkstatt für Reparaturen:
SERVICE-CENTER
Schorndorfer Straße 70
D-71332 Waiblingen
Telefon (0 7151) 5 68 08 - 60
Telefax (0 7151) 5 68 08 - 64
Wir holen Ihre Maschinen und Werkzeuge bei Ihnen ab!
Nutzen Sie in der Bundesrepublik Deutschland unseren Abholservice.
Einfach anrufen unter Telefon (0 7151) 5 68 08 - 60.
Oder wenden Sie sich an eine andere autorisierte REMS Vertrags-Kunden-
dienstwerkstatt in Ihrer Nähe.

General Safety Rules

WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term „power tool" in
all of the warnings listed below refers to your mains operated (corded) power
tool or battery operated (cordless) power tool, also machines and electric units.
Only use the power tool for the purpose for which it was intended, with the due
attention to the general safety and accident prevention regulations.
SAVE THESE INSTRUCTIONS.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite acci-
dents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock. If
the power tool comes with an earthed wire, the plug may only be connected
to an earthed receptacle. At work sites, in damp surroundings, in the open
or in the case of comparable types of use, only operate the power tool off
the mains using a 30 mA fault current protected switch (FI breaker).
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or un-
plugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
C) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of in-
attention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position be-
fore plugging in. Carrying power tools with your finger on the switch or plug-
ging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may re-
sult in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collec-
tion facilities, ensure these are connected and properly used. Use of
these devices can reduce dust related hazards.
h) Only allow trained personnel to use the power tool. Apprentices may
only operate the power tool when they are over 16, when this is necessary
for their training and when they are supervised by a trained operative.
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the ra-
te for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
eng