Sanyo SPW-C706VH8 Instrucciones De Instalación página 77

Automatic address setting using the remote controller
Case 3
●
If the power can be turned ON separately for the indoor and
outdoor units in each system (indoor unit addresses can be
set without running the compressor):
Individual system automatic address setting: Display item code
"A1".
(1) Press the remote controller timer time
button simultaneously.
(Hold for 4 seconds or longer.)
↓
(2) Then press either the temperature setting
button.
(Confirm that the item code is "A1".)
↓
(3) Use either the
outdoor unit to perform automatic address setting for. Then
press the button.
("R.C.1" is displayed, and automatic address setting is
performed for refrigerant system 1.)
When automatic address setting for system 1 is completed,
the units return to normal stopped status.
<Approximately 4 – 5 minutes are required.>
During automatic address setting, "SETTING" blinks on the
remote controller display. This display disappears when
address setting is completed.
Case 4
●
If the power cannot be turned ON separately for the indoor
and outdoor units in each system:
(The compressors must be run in order to automatically set
the indoor unit addresses. Therefore perform this step after
completing the refrigerant tubing work.)
All-systems automatic address setting: Display item code "AA".
(1) Press the remote controller timer time
button simultaneously. (Hold for 4 seconds or longer.)
↓
(2) Next press the button.
(Automatic address setting is performed in sequence for
all outdoor units from No. 1 to No. 30. When automatic
address setting is completed, the units return to normal
stopped status.)
<Approximately 15 minutes is required for each system.>
↓
During automatic address setting, "SETTING" blinks on the
remote controller display. This display disappears when
address setting is completed.
button and
or button to select the
button and
Fig. 10-18
10-22-2. Setting outdoor unit system addresses
For the basic wiring diagram (Set the system addresses: 1, 2, 3...)
Outdoor unit control PCB
System address rotary switch
(Set to "0" at time of shipment)
System address rotary switch
System address
10s
ON
or
1
8 – 10 HP
63PH (CN027, WHT)
FUSE (0.5A, F500)
EXCT
(CN030, RED)
RC P
(CN039, RED)
IC002
FUSE
(6.3A, F101)
CTL2
(CN202, GRN)
CTL1
(CN203, GRN)
N . P . C H E C K
(CN046, RED)
R.C.ADD. Rotary switch
System address
0 Automatic address
(Setting at shipment = "0")
1 (If outdoor unit is No. 1)
2 (If outdoor unit is No. 2)
11 (If outdoor unit is No. 11)
21 (If outdoor unit is No. 21)
30 (If outdoor unit is No. 30)
75
8 – 10 HP
20s DIP switch
ON
2
OFF
OC (CN500, BLU)
EMG (CN502, BRN)
LED2
LED1
MODE (CN038)
IC001
System address
10s digit
No.
(2P DIP switch)
Both OFF
ON
1 2
Both OFF
ON
1 2
Both OFF
ON
1 2
10s digit ON
ON
1 2
20s digit ON
ON
1 2
10s digit and 20s
digit ON
ON
1 2
SILENT (CN037, WHT)
PUMP DOWN (CN048)
TEMINAL (CN205, BLK)
C2 (CN020, WHT)
C1 (CN021, WHT)
TS (CN022, RED)
TO (CN023, BLK)
TD (CN024, BLK)
MOV1
(CN300, WHT)
MOV2
(CN301, BLK)
LED (D041)
EEPROM
TEST (CN033, RED)
C-CHK (CN035)
A.ADD (CN047)
R.C.ADD. DIP switch
D115
Fig. 10-19
System address
1s place
(Rotary switch)
"0" setting
ON
OFF
"1" setting
ON
OFF
"2" setting
ON
OFF
"1" setting
ON
OFF
"1" setting
ON
OFF
"0" setting
ON
OFF