Makita DVC150L Manual De Instrucciones página 12

Before using the po der filter, make
NOTICE:
sure that prefilter and damper are al ays used
together. It is not allowed to install powder filter solely.
Installing the ater filter
Optional accessory for cloth filter model
CAUTION:
Never pick up water or wet dust with-
out the oat and the cloth filter or the ater filter.
CAUTION:
For picking up wet dust, make sure that
the oat cage and the oat are installed on the cleaner.
When installing the ater filter on
CAUTION:
the tank, set it tight at the opening of the tank so
that the hook of the ater filter engages the tank
opening firmly and there is no space bet een the
ater filter and the tank.
To pick up water or wet dust only, the water filter is more
suitable than the cloth filter.
When installing the water filter, align its mounting posi-
tion mark w it h t h e one on t h e tank.
Fig.15: 1. Water filter 2. T ank 3. Mounting position
marking
NOTE: It is recommended using water filter when
pi c king up large amount o f w ater repeate d l y .
O t h er w ise v a c uum abilit y ma y be re d u c e d in c ase o f
cloth filter.
Installing the paper pack
Optional accessory
WARNING:
W hen using the paper pack, also
use the cloth filter or prefilter together that is
preinstalled on the cleaner. F ailure to use t h e c lot h
filter / prefilter together may cause unusual noise and
heat, resulting in a fire.
(For the cloth filter model)
CAUTION:
• Never pick up water or other liquids or wet
dusts when using the paper pack. P i c king
up su c h t h ings ma y c ause t h e paper pa c k
breakage.
• Before using the paper pack, make sure that
po der filter (optional accessory), damper
(optional accessory) and prefilter are al ays
used together.
(For the powder filter model)
CAUTION:
• Before using the paper pack, make sure
that po der filter, damper and prefilter are
always used together.
1. R emo v e t h e rubber h ol d er.
Fig.16: 1. R ubber h ol d er
2. E x ten d t h e paper pa c k.
3. A lign t h e paper pa c k opening w it h t h e d ust su c tion
opening o f t h e c leaner.
4. I nsert t h e c ar d boar d o f t h e paper pa c k onto t h e
h ol d er so t h at it is positione d at t h e en d be y on d t h e
d etent protrusion.
Fig.17: 1. P aper pa c k 2. H ol d er
Installing the polyethylene bag
C leaner c an also be use d w it h out pol y et h y lene bag.
H o w e v er, using pol y et h y lene bag is easier to empt y t h e
tank w it h out letting y our h an d s d irt y .
S prea d t h e pol y et h y lene bag in t h e tank. I nsert it bet w een
t h e h ol d er plate an d t h e tank, an d pull it to t h e h ose inlet.
Fig.1 8 : 1. H ol d er plate 2. P ol y et h y lene bag
S pread th e bag around th e top of th e tank so th at th e c loth
filter / prefilter edge can catch and hold the bag securely.
Fig.19: 1. Cloth filter / prefilter
NOTE: A pol y et h y lene bag a v ailable on t h e
market c an be use d . 0.0 4 mm or t h i c ker one is
re c ommen d e d .
NOTE: T oo mu c h d ust w ill tear t h e bag easil y , so
d o not c olle c t t h e d ust more t h an t h e h al f o f t h e bag
c apa c it y .
Emptying the polyethylene bag
WARNING:
is switched off, unplugged, and the battery car-
tridge is removed before emptying the polyeth-
ylene bag. F ailure to d o so ma y c ause an ele c tri c
shock and serious personal injury.
CAUTION:
Do not apply a great impact on the
oat cage and tank. A ppl y ing a great impa c t ma y
c ause d e f ormation an d d amage to t h e parts.
CAUTION:
Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. O r, t h e su c tion f or c e w ill w eaken an d t h e
motor ma y be broken.
CAUTION:
Do not grab the hook when empty-
ing the tank. G rabbing t h e h ook ma y c ause t h e h ook
to break.
U n h ook an d li f t up t h e tank c o v er.
Shake off the dust from the cloth filter / prefilter and then
take t h e pol y et h y lene bag out o f t h e tank.
Fig.20
NOTE: T ake t h e pol y et h y lene bag c are f ull y out o f t h e
tank so t h at t h e pol y et h y lene bag c annot be c aug h t
an d torn b y t h e protrusion insi d e t h e tank w h en emp-
t y ing it.
NOTE: Empt y t h e pol y et h y lene bag be f ore it
be c omes f ull. T oo mu c h d ust in t h e tank ma y c ause
t h e pol y et h y lene bag to be torn.
Installing the tool box
1. R elease t h e lo c k o f t h e batter y c o v er, an d open
t h e batter y c o v er.
2. S et t h e rails on t h e tool bo x along t h e groo v es on
t h e h ousing.
3. C lose t h e batter y c o v er an d appl y t h e lo c k.
Fig.21
T h e tool bo x is c on v enient f or c arr y ing batteries, e x ten-
sion c o d e, pipe, or c u f f s.
Fig.22
12 ENGLISH
Always make sure that the cleaner