Operation - EINHELL TE-MS 18 /210 Li-Solo Manual De Instrucciones

(14). The saw has locking positions at the
following angles: -45°, -40°, -35°, -30°, -22.5°,
-15°, -10°, -5°, 0°, 5°, 10°, 15°, 22.5°, 30°,
35°, 40° and 45°.
•
To release the saw from its position at the
bottom, pull the fastening bolt (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing up the machine head (4).
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
Always fasten the clamping device (8) with
the locking screw (26).
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(33).
•
- To move out the workpiece supports (10)
press the lever on the bottom side of the
workpiece support and then pull the workpie-
ce support outwards to the right or left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (13).
•
When the locking grip (21) is undone, you
can tilt the machine head (4) to the left by up
to 45°.
5.3 Precision adjustment of the stop for
crosscut 90° (Fig. 1.6-7)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the machi-
ne head (4) all the way to the right using the
handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally, check the position of the pointer (20)
on the scale (19). If the pointer (20) still does
not show the correct angle on the scale, it can
be readjusted.
•
To readjust it, undo the fastening screw on
the pointer (20) using a screwdriver. Move the
pointer to the desired scale position and then
retighten the fastening screw.
•
The angle stop and hexagon key (d) are not
included in the scope of this delivery – they
are available from your dealer.
Anl_SA_TE_MS_18_20_Li_Solo_SPK8.indb 37 Anl_SA_TE_MS_18_20_Li_Solo_SPK8.indb 37
GB
5.4 Precision adjustment of the stop for 45°
miter cuts (Fig. 1, 8-9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
The angle stop and Allen key (d) are not in-
cluded in the scope of this delivery – they are
available from your dealer.
5.5 Adjusting the miter angle on the machine
head (Fig. 2, 12-13)
•
Undo the locking grip (21).
•
Hold the machine head (4) by the handle (1).
•
After the locking grip is undone, the machine
head can be infinitely tilted as well as tilted to
various locking positions.
•
Angles to the left: 0-45°
•
Re-tighten the locking grip (21).

6. Operation

6.1 Charging the Li battery pack (Fig. 2, 15)
1. Remove the rechargeable battery (39) from
the mount (40) by pressing the pushlock
button on the battery and pulling it out of the
mount.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(41) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
- 37 -
15.03.2018 14:19:55 15.03.2018 14:19:55