V2 VEO-RFE Serie Manual De Instrucciones página 20

SWITCH 1: STORAGE OF THE TRANSMITTERS
AND SELECTION OF THE MODE AWNING
m
WARNING: the first transmitter stored fixes the direction of
motion of the motor.
To store a transmitter TX1 on a blank control unit proceed
as follows:
1. Power only the control unit to be programmed
2. Set on ON the switch 1 of the transmitter.
3. Multichannel transmiter only: press several times the key SELC
of the transmitter TX1 until displayed the selected channel (by
the leds or on the display).
4. Press and keep pressed (for about 5 seconds) the key PROG of
the transmitter TX1 until the motor starts to move in one way.
5. Release the key PROG: the motor stops.
6. Press the keys UP or DOWN depending on the way of motion
of the roll-up shutter before stopping:
- if the roll-up shutter was going up, press the key UP;
direction acquired: the key UP moves the roll-up shutter
UPWARDS, the key DOWN moves the roll-up shutter
DOWNWARDS.
- if the roll-up shutter was going down, press the key
DOWN; direction acquired: the key DOWN moves the roll-
up shutter DOWNWARDS, the key UP moves the roll-up
shutter UPWARDS.
7. Set the switch 1 to OFF.
8. Try to operate the roll-up shutter and check that it works
with the logic above described. If the logic is reversed, it is
necessary to delete all the codes stored (read Switch 3) and
start again the above procedure.
To add another transmitter TX2 to the control unit it is
necessary to use a remote control previously stored (TX1)
and proceed as follows:
1. Multichannel transmiter only: press several times the key SELC
of the transmitter TX1 until displayed the channel stored (by
the leds).
2. Multichannel transmiter only: press several times the key SELC
of the new transmitter TX2 until display the channel to be
stored (by the leds).
3. Take the roll-up shutter to half its way with TX1.
4. Set to ON the switch 1 of the transmitter TX1.
5. Press and keep pressed for about 5 seconds the key PROG of
the TX1 until the motor starts to move.
6. Release the key PROG, the motor stops.
7. Press the key UP or DOWN of the TX2: the transmitter is
stored with the same logic of the TX1.
SWITCH 2: STORING OF THE TRANSMITTERS
AND SELECTION OF THE MODE ROLLING
SHUTTER
m
WARNING: the first transmitter stored fixes the direction of
motion of the motor.
To store a transmitter TX1 on a blank control unit proceed
as follows:
Repeat the procedure described for switch 1 using, however, only
switch 2
SWITCH 3: DELETION OF ALL THE STORED
TRANSMITTERS
To delete all the transmitters stored on the control unit it
is necessary using a remote control previously stored and
proceed as follows:
1. Power only the control unit to be programmed
2. Multichannel transmiter only: press several times the button
SELC on the transmitter until displayed the channel stored
(by the leds)
3. Position the roll-up shutter at the mid-height.
4. Set on ON the switch 3 of the transmitter.
5. Press and keep pressed the button PROG of the transmitter
until the motor moves in both the ways for 1 second, showing
the end of deletion.
6. Release the button PROG and set on OFF the switch 3 of the
transmitter.
To delete all the codes by means of a transmitter non-
stored, proceed as follows:
1. Position the retractable at the mid-height.
2. Switch off power supply of the system.
3. Set on ON the switch 3 of a transmitter.
4. Press and keep pressed the button PROG.
5. Supply power only to the control unit on which to make the
deletion: after about 1 second the motor moves in both the
ways showing the correct deletion.
6. Release the button PROG and set on OFF the switch 3.
- 20 -