Status Display - Siemens SIRIUS 3RW44 2 Serie Instructions De Service

Display measured value
ESC OK
Device status
Phase voltages
Active parameter set
UL1N
Parameter set 1
UL2N
Parameter set 2
UL3N
Parameter set 3
Phase-to-phase voltages
Type of connection
UL1-L2
Unknown/faulty
UL2-L3
Star/delta
UL3-L1
Inside delta
Blocking voltages
Direction of rotation
ULT1
Unknown
ULT2
Clockwise
ULT3
Counter-clockwise
Phase currents
Inputs
IL1
Status - Inputs
IL2
Input 1 - Action
IL3
Power
Line frequency
Supply voltage
Heatsink temperature
Motor heat build-up
Remaining time for tripping
Switch off standard display
Input 2 - Action [...]
Input 3 - Action [...]
Input 4 - Action [...]
Outputs
Status - Outputs
Output 1 - Action
Output 2 - Action [...]
Output 3 - Action [...]
Output 4 - Action [...]
Order number
Firmware information
Version
Date
* Delivery version 2
** Possible only in connection with creep speed
3ZX1012-0RW44-1AA1
3RW44 Menu structure

Status display

ESC OK
Parameter set 1
Motor 1
Rated operating current Ie
Rated operating torque
Rated operating speed
Copy motor data to PS2 + 3
Starting settings
Starting mode
Voltage ramp
Voltage ramp + current limiting
Torque control
Torque control + current limiting
Direct on line
Motor heating *
Start voltage
Start torque
Limiting torque
No Action
Starting time
Manual operation local
Maximum starting time
Emergency start *
Current limiting value
Slow speed
Breakaway voltage
Quick stop *
Breakaway time
Trip reset
Motor thermal capacity *
Motor right PS1
Stopping settings
Motor left PS1 **
Stopping mode
Motor right PS2
Motor left PS2 **
Motor right PS3
Motor left PS3 **
Stopping time
Stopping torque
Dynamic braking torque
DC
Slow speed- parameters
No Action
Slow speed factor right
PIO output 1
Slow torque right
PIO output 2
Slow speed factor left
Input 1
Slow torque left
Input 2
Current limit values
Input 3
Minimum current limit
Input 4
Maximum current limit
Run up
Parameter set 2 [...]
Bypass operation
Parameter set 3 [...]
Coasting down
Inputs
On time motor
Input 1 - Action
Command motor-on
No Action
DC braking contactor
Manual operation local
Group warning
Emergency start *
Group error
Slow speed
Bus error
Quick stop *
Device error
Trip reset
Power on
Motor right PS1
Ready to start
Motor left PS1 **
Motor right PS2
Motor left PS2 **
Motor right PS3
Motor left PS3 **
Input 2 - Action [...]
Input 3 - Action [...]
Input 4 - Action [...]
Outputs
Output 1 - Action
No action
PIO-output 1
PIO-output 2
Input 1
Input 2
Input 3
Input 4
Run up
Bypass operation
Coasting down
On time motor
Command motor-on
DC braking contactor
Group warning
Group error
Bus error
Device error
Power on
Ready to start
Settings
ESC OK
Coasting down
Torque control
Pump stop
DC braking
Combined braking
braking torque
Output 2 - Action [...]
Output 3 - Action [...]
Motor protection
Tripping class
None
CLASS 5 (10a)
CLASS 10
CLASS 15
CLASS 20
CLASS 30
Current asymmetry limit value
Prewarning limit tripping reserve
Prewarning limit motor heat build-up
Idle time
Pre-charge time
Protection against voltage failure
No
Yes
Temperature sensor
Deactivated
Thermo click
PTC type A
Display settings
Language
English
Deutsch
Français
Español
Italiano
Português
Contrast
Lighting
Brightness
Lighting on
Off with time delay
Lighting off
Response to fault
Unchanged
On
Blinking
Flickering
Response to warning
Unchanged
On
Blinking
Flickering
Reaction time keys
Auto repeat
Time
Speed
Activity monitoring time
Response to...
Overload - therm. motor model
Tripping without restart
Tripping with restart
Warning
Overload - temperature sensor
Tripping without restart
Tripping with restart
Warning
Current limit value violation
Warning
Tripping
Overload - contact block
Tripping without restart
Tripping with restart
Asymmetrie
Warning
Tripping
Earth fault
Warning
Tripping
Name
Name
Saving options
Save settings
Restore settings
Restore basic factory settings
19