Beninca CP.BN Manual De Instrucciones página 15

MENU
By selecting this function, the receiver awaits (
tion.
PP
Press the transmitter key to be assigned to this function.
If the code is valid, it is stored in memory and OK appears.
If the code is not valid, the wording
By selecting this function, the receiver awaits (
nel.
Press the transmitter key to be assigned to this function.
2Ch
If the code is valid, it is stored in memory and OK appears.
If the code is not valid, the wording
If the 2CH logics is preset to OFF, the key assigned to 2CH function carries out the pedestrian control signal.
By selecting this function, the receiver awaits (
CLR
If the code is valid, it is erase and OK appears.
If the code is not valid or is not in memory, the wording
RTR
Completely erase the receiver memory. Confirmation of operation is required.
IMPORTANT, PLEASE READ CAREFULLY:
The radio receiver in this product is compatible with the new ARC (Advanced Rolling Code) transmitters which, thanks to 128-bit
encryption ensure superior copy-security.
Storing new ARC transmitters is quite similar to that of normal rolling code transmitters with HCS coding, but be aware that:
1) ARC transmitters and Rolling Code HCS can not be stored in a single receiver.
2) The first transmitter memorized determines the type of transmitters to be used later. If the first transmitter memorized is ARC, you
can not store Rolling code HCS transmitters, and vice versa.
3) Fixed code transmitters may only be used in conjunction with Rolling code HCS transmitters, bringing the logic CVAR OFF. They
are, therefore, not usable in combination with the ARC transmitters. If the first rolling code transmitter stored is an ARC CVAR the
logic is inoperative.
4) If you want to change the type of transmitters it is necessary to proceed with a receiver reset.
If a transmitter code is already stored in the receiver, the radio remote copy can be carried out (without accessing to the control unit).
IMPORTANT: This procedure should be performed with gate leaves open, during the TCA dwell time.
Proceed as follows:
1 Press the hidden key of the already memorised transmitter.
2 Within 5 seconds, press the key of the already memorised transmitter which corresponds to the channel to be matched with the
new transmitter code. The flashing light switches on.
3 Within 10 sec, press the hidden key of the new transmitter.
4 Within 5 sec, press the key of the new transmitter to be matched to the channel selected at point 2. The flashing light switches off.
5 The receiver memorises the new transmitter and exits immediately the programming mode.
MENU
The number of cycles (open+close) completed by the system is displayed.
When the push-button <PG> is pressed once, the first 4 digits are displayed, if the push-button is pressed
NMAN
once more, the last 4 digits are displayed.
E.g. <PG> 0012 >>> <PG> 3456: 123.456 cycles were performed.
RESET of the control unit. WARNING: This resets the control unit to the default values.
When the <PG> push-button is pressed once, the RES wording begins to flash, if the push-button <PG> is
RES
pressed once more, the control unit is reset.
Note: neither the transmitter codes nor the position and stroked of the gate leaf will be erased from the re-
ceiver.
Autoset of the control unit.
WARNING: during this operation, the gate leaves movement MUST be free from obstacles.
First pressure of the <PG> push-button causes the SET wording to flash at 1 sec intervals. If the <PG> push-
button is pressed again, the autoset frequency of the control unit is carried out.
If the autoset sequence has a positive result, the wording "OK" appears on the display; conversely, the "Err"
SET
wording is displayed ( the autoset should be repeated).
If, during the autoset sequence, any input is activated (PP,PED,PHOT,STOP), the procedure stops immediately
and the wording "Err" is displayed.
Note: The autoset presets the torque values of the motors. At the end of operation, check the correctness of
the preset values and possibly modify them by hand through the appropriate Menu.
RADIO (RADi)
is displayed.
Err
is displayed.
Err
ARC COMPATIBLE CONTROL UNIT
REMOTE COPY OF TRANSMITTER CODES
FUNCTION
) for a transmitter code to be assigned to the step-by-step func-
Push
) for a transmitter code to be assigned to the second radio chan-
Push
) for a transmitter code to be erased from memory.
Push
is displayed.
Err
FUNCTION
15