Transportation And Storage - Ryobi RCS3835T Manual De Instrucciones

chainsaw. Their size and fl exibility can easily cause the
saw to bounce towards you or bind up with enough force
to cause a kickback. The best tool for that kind of work is
a hand saw, pruning shears, an axe or other hand tools.
Bucking a log
See page 349.
Bucking is cutting a log into lengths. It is important to
make sure your footing is fi rm and your weight is evenly
distributed on both feet. When possible, the log should be
raised and supported by the use of limbs, logs or chocks.
Follow the simple directions for easy cutting. When the log
is supported along its entire length, it is cut from the top
(overbuck).
When the log is supported on one end, cut 1/3 the diameter
from the underside (underbuck). Then make the fi nished
cut by overbucking to meet the fi rst cut.
When the log is supported on both ends, cut 1/3 the
diameter from the top (overbuck). Then make the fi nished
cut by underbucking the lower 2/3 to meet the fi rst cut.
When bucking on a slope, always stand on the uphill side
of the log. When "cutting through", to maintain complete
control release the cutting pressure near the end of the cut
without relaxing your grip on the handles of the product.
Don't let the chain contact the ground. After completing the
cut, wait for the saw chain to stop before you move the
product. Always stop the engine before moving from tree
to tree.
Limbing a tree
See page 350.
Limbing is removing the branches from a fallen tree. When
limbing, leave larger lower limbs to support the log off the
ground. Remove the small limbs in one cut. Branches
under tension should be cut from the bottom up to avoid
binding the product.
Springpoles
See page 350.
A springpole is any log, branch, rooted stump, or sapling
which is bent under tension by other wood so that it springs
back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous. Do not attempt to cut
bent branches or stumps which are under tension unless
you are professionally trained and competent to do so.

TRANSPORTATION AND STORAGE

■ Stop the engine, engage the chain brake, and
disconnect the spark plug wire from the spark plug.
Allow the product to cool down before storing or
transporting.
■ Clean all foreign material from the product.
■ Drain all fuel from tank into a container approved for
petrol. Remember to properly replace and tighten the
fuel mix cap.
■ Run the engine until it stops. This will remove all fuel-
lubricant mix that could become stale and leave varnish
and gum in the fuel system.
■ Drain all bar and chain lubricant from tank into a
container approved for lubricant. Remember to properly
replace and tighten the chain lubricant cap.
■ Always fit guide bar cover before storing the product, or
during transportation.
■ Store the product in a cool, dry, and well-ventilated
place that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and de-
icing salts. Do not store outdoors.
■ When carrying the product for short distance (from one
working area to the next), always apply the chain brake
so that the saw chain is restricted from movement.
■ When transporting the product, secure it against
movement or falling to prevent injury to persons or
damage to the product.
■ Never carry or transport the product while the engine
is running.
■ Abide by all government and local regulations for the
safe storage and handling of petrol. Excess fuel should
be used in other 2-cycle engine powered equipment.
MAINTENANCE
Always keep the product in good working condition.
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualifi ed service
technician. For servicing and repairs, have the product
serviced by an authorised service centre only. When
servicing, use only original replacement parts.
WARNING
Before inspecting, cleaning, or servicing the product,
stop the engine, engage the chain brake, and disconnect
the spark plug wire from the spark plug. Failure to follow
these instructions can result in serious personal injury or
property damage.
■ You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service centre.
■ Consequences of improper maintenance, removal, or
modification of safety features like the chain brake,
ignition switch, hand guard (front and back), spiked
bumper, chain catcher, guide bar, low-kickback saw
chain may cause the safety features to not function
correctly, thus increasing the potential for serious injury.
Keep the product professionally maintained and safe.
■ Sharpening the chain safely is a skilled task. Therefore,
the manufacturer strongly recommends that a worn or
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English | 7