Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4.3
Programmable parameters
DISPLAY FUNCTION
Logic: 0 = Automatic;
LO
3 = Semi-automatic 1; 4 = Semi-automatic 2; 5 = Manned; 6 = Timer
PA
Pause time (0"- 60") (1 step =1")
En.
Force (thrust force on obstacle)
SO.
Speed on OPENING stroke
SC.
Speed on CLOSING stroke
SP.
SPECIAL logic: 0 = nol; 1 = yes;
CM.
Change hand confi guration; 0= RH ; 1= LH
CP.
Barrier class (beam length in metres): 0=2.0 ÷ 2.5 ; 1=3 ; 2=3.5 ; 3=4 ; 4=4.5
PSET
Restore factory settings (default)
PRoF
To enter the programming mode
A1
Pre-slowing start on opening stroke (as % of total travel)
A2
Pre-slowing start on closing stroke (as % of total travel)
A3
Pre-slowing speed on opening stroke
A4
Pre-slowing speed on closing stroke
A5
Pre-fl ashing on opening stroke
A6
Pre-fl ashing on closing stroke
A9
MASTER/SLAVE 0=none; 1= MASTER card ; 2= SLAVE card
START in pause (AUTOMATIC LOGIC); 0 = No effect ; 1 = Reloads the
AA
pause time ; 2 = Stop the barrier in the open position.
Closing when the photocell is no longer covered occurs:
1= immediately if the pause time has elapsed
Ab
2 = after 10 seconds
03 = after a complete new period of pause time (reloads the pause time)
Obstacle recognition on closing stroke; 0 = REOPEN (in the AUTOMATIC
Ad
mode, recloses after the pause) after 3 attempts wit reversing will remain open; 1
= REOPEN and stops in the open position.
AE
Safety device during opening: (0 = safety edge; 1 = photocell)
Operation in emergency mode with batteries following a power supply failure
(indicated by rapid fl ashing)
AF
00 = Runs 3 cycles and then remains closed
01 = Runs 3 cycles and then stops open
02 = Opens and stays open (safety functioning)
LA
Tooled beam lighting programmable Output: (0 = 12V; 1 = 24V)
Closing photocell operational check (0 = disabled; 1 = enabled) Carried out
tF
before each movement (with exception of ER-REF); in the event of any fault ER01
AL.t
Total cycle counter, cannot be modifi ed (increases by 1 ever 100 cycles)
AL.P
Partial cycle counter (1 = 10 cycles) (reset using AL.S or AL.r)
Sets the maintenance cycle on the partial cycle counter (1 = 10 cycles) in minimum
AL.S
steps of 100 cycles. Each setting operation resets the AL.P counter.
AL.r
Resets the AL.P counter
rn.
Cancels a remote control whose address you know (see Saving remote controls)
r.tr
Cancels all the remote controls (see Saving remote controls)
UPLd
Saves to an Optional external Memory Module the remote controls of the control unit
dnLd
Saves to the control unit the remote controls of the Optional external Memory Module
4.4
Parameters RESET
If you want to return all the programmed parameters to their default settings, you should RESET the unit as follows:
• Start BASIC programming. Scroll through the parameters and select
button for 3 seconds.
The display will show the fl ashing
then display the message
• To leave this function and continue with programming, press the YELLOW button.
PTR-24
IMPORTANT:
1 = Semi-automatic Open/Close;
LO
0
.
.
Blue
Red
To select
To confi rm
PSET
. Confi rm this selection by pressing the RED
def
message while the default settings are restored and will
- 27 -
CONTROL UNIT
Yellow
To exit
VALUES
2 = Park;
0 ÷ 6
0 ÷ 60
0 ÷ 5
50 ÷ 80
50 ÷ 80
0 ÷ 1
0
0 ÷ 1
0
0 ÷ 4
RED button to confi rm
RED button to confi rm
01 ÷ 50
01 ÷ 50
30 ÷ 50
30 ÷ 50
1 ÷ 5
1 ÷ 5
0
÷
0
2
÷
0
2
÷
1
3
÷
0
1
÷
0
1
÷
0
2
÷
0
1
÷
0
1
÷
0000
9999
÷
0000
9999
÷
0000
9999
RED button to confi rm
÷
0
99
RED button to confi rm
RED button to confi rm
RED button to confi rm
DEFAULT
0
(automatic)
25
0
70
70
0
(no)
(Right-hand)
(2.0 ÷ 2.5m)
20
(%)
20
(%)
30
30
3
3
(Single barrier)
1
3
(reloads the
pause time)
0
1
0
0
0
-
0000
-
00
Publicidad
Capítulos
Tabla de contenido
