Saving The Remote Controls On The Built-In Receiver; With The Optional Receivers, Unico (Memory System) Or Rpl-Eco; Functional Tests And Adjustments - Aprimatic PTR-24 Instrucciones Para La Instalación Electrica, El Uso Y El Mantenimiento

3.2

Saving the remote controls on the built-in receiver

To program the remote controls so they are recognised by the system, follow
the instructions below.
At the end of programming, button 1 will give the START command and button
2 will give the PEDESTRIAN START command (see fi gure).
IMPORTANT! The barrier must be closed before you can start saving or
cancelling settings.
Activating the teach function
1 Press all the buttons of the
first remote control to be saved
or of a remote control which
has already been saved. (The
receiver memory must be
empty).
teach function for 30 seconds.
- Confirmed by: the displays
show SEED.
30"
During the programming time you can
save the first and any other remote
controls as required.
After 30 seconds, the teach function
ends.
- Confirmed by: the LED switches off.
If you wish to save a new remote
control, activate the teach function
again using a remote control which
has already been saved and repeat
the step
end
IMPORTANT NOTE:
To LEAVE programming before the 30 seconds has elapsed, press one of the buttons on the programmed remote control; all the
●
values confi rmed will be saved.
To CANCEL all the programmed remote controls, use the
●
NOTE: To confi rm that you really want to cancel the programming, press the RED button when the message
this the display will show the following messages rapidly, one after the other:
to LEAVE programming.
To CANCEL a single remote control, call up parameter
●
of the remote control you wish to cancel and then confi rm cancellation by pressing the RED button. NOTE: To confi rm that you
really want to cancel the programming, press the RED button when the message
following messages rapidly, one after the other:
To export all the remote controls saved you require a plug-in memory module (see our catalogue). To export remote controls, see
●
the instructions with the parameters
RvN
appears. After this the display will show the following messages in quick succession:
button, to LEAVE programming.
To SHOW the address of a already saved remote control: press all the buttons of this remote control
●
press now any button of it
3.2.1

With the optional receivers, Unico (Memory System) or RPL-ECO

WARNING! To use the optional Unico (Memory System) or CRPL-ECO receivers, unplug and remove the built-in receiver
and its antenna (see unit layout diagram).
Plug the UNICO receiver into the connector CN2 or the RPL-ECO receiver into the connector CN1 (see unit layout diagram).
●
Connect the antenna and complete the remote control teach programming using the instructions supplied with the receiver.
●
3.3

Functional tests and adjustments

Start the system and perform the functional tests. Implement the safety precautions. You can adjust the following parameters
(see the section Programming):
PTR-24
This enables the
.
30"
rn
DELL FREE
,
UPLd dnLd
and . NOTE: To confi rm the operation, press the RED button when the message
the displays show its address.
operating speed; thrust on obstacle;
NOTE:
These instructions are only valid for remote controls in
mode 0.
Saving the first remote control
2 Press any button on the remote
control.
- Confirmed by: the displays show
MEMO for 2 seconds and then the
remote control address (000).
!
Make a note of the address so that
you can cancel the remote control
whenever you want at a later date.
Saving multiple remote controls
30"
3 Press all the buttons of a new remote control to
be saved.
4 Press any button of this remote control.
- Confirmed by: the displays show
mem0, and then the address (from
001 to 099).
!
Make a note of the address.
Save all the other remote controls
one at a time repeating steps 3
and 4 for each remote control
(
Remember to make a note of the
addresses
!
The programming time restarts at
the end of each saving operation.
r tr
. menu on the advanced programming menu (see related section).
DELL FREE
, and
00
. in the advance programming menu. Scroll through to the address
SURE
appears. After this the display will show the
ESC
and . Now, press the YELLOW button, to LEAVE programming.
approach time.
- 25 -
CONTROL UNIT
2 1
1 3
).
SURE
appears. After
ESC
. Now, press the YELLOW button,
SAUE ESC
and . Now, press the YELLOW
the displays show
2
4
SEED
;