Full-Overlay Custom Panels - Thermador KBULT3651A Instrucciones De Instalación

Ocultar thumbs Ver también para KBULT3651A:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Door Panel - Side View
¹⁄₂
" (1.3 cm)
F u l l - O ve r l a y C u s t o m Pa n e l s
Custom overlay panels allow you to blend the exterior of your
refrigerator into the overall kitchen décor and to use custom
handles for additional design flexibility.
NOTE: To use full-overlay custom panels, a Trimless Trim Kit for
36" Bottom-mounts is required (TRIMKITBM). Full-overlay
custom panels and handles are required but not included. Create
the panels according to these specifications. You may order
Thermador's Curved Handle Kit (CURVEDHAND) or select
handles from another source. See the "Models" section under
"Design Specifications" for additional information.
The custom panels must have backer panels attached in order to
mount them to the refrigerator. It is most common to work with
three panels, as shown in the following graphic: a decorative
overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and
a ¹/₄" (6.35 mm) backer panel.
Overlay Panel
Spacer Panel
Backer Panel
5
/
" to
3
/
"
8
4
1
/
"
4
(15.88 to
1
(6.35 mm)
/
"
8
19.05 mm)
(3.18 mm)
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimension and placement instructions to be sure that the
custom overlay panels will fit properly.
IMPORTANT:
The total weight of the refrigerator door overlay panel cannot
exceed 60 lbs (23 kg).
The total weight of the freezer drawer overlay panel cannot
exceed 30 lbs (13.5 kg).
The total weight of the top grille overlay panel cannot exceed
10 lbs (4.5 kg).
10
¹⁄₄
"
(6.35 mm)
max.
min.
Spacer Panel
1
/
"
8
(3.18 mm)
1" minimum
(2.54 mm)
Door/Grille Trim
Offset Dimension
To minimize panel weight, you may use 2" (5.08 cm) spacer strips
around the perimeter in place of full-sheet solid spacer panels.
The spacer strips must be set in at least 1" (2.54 cm) from the
top, bottom and sides edges of the backer panel. If you use
spacer strips, it is also recommended that you use two - 2"
(5.08 cm) strips horizontally centered for added support.
7
3
/
"
8
(18.73 cm)
34
8
1
/
"
2
(21.59 cm)
49
1
/
"
8
(124.78 cm)
50"
(127.0 cm)
(87.63 cm)
20
9
/
"
16
(52.23 cm)
20
3
/
"
16
(51.28 cm)
35
3
/
"
8
(89.85 cm)
Center
Backer
Panel
5
/
" (87.95 cm)
8
left to
right
Bottom Offset
1" (2.54 cm)
34
1
/
"
2
(87.63 cm)
34
5
/
"
16
(87.15 cm)
Center
Backer
Panel
left to
right
Bottom Offset
7
/
" (11.1 mm)
16
34
1
/
"
2
34
5
/
"
16
Center
(87.15 cm)
Backer
Panel
left to
right
Bottom Offset
1
/
" (1.6 mm)
16

Publicidad

Tabla de contenido
loading

Tabla de contenido