EdilKamin NANCY Instalación Uso Y Mantenimiento página 33

ress and hold the " " ey on the remote control for seconds. his turns on the cloc regulation and by pressing the
ey, the wee ly timer function is accessed, with the display showing the description " RO RA
his function allows you to set a number of times the insert turns on and off per day (up to a maximum of three), each
day of the wee .
As you con rm the display with the ey " ", one of the following options will appear:
NO RO . (no programme set)
DAILY RO RA (single programme for every day of the wee )
EE LY RO RA . (speci c programme for each day individually)
se the " " and " " eys to switch between programmes.
se ey " " to con rm the option "DAILY RO RA " to choose the number of programmes (turn on/off) to be carried out per
day.
se the "DAILY RO RA " to set identical programme/s for every day of the wee .
By then pressing the " " ey, the following can be seen:
- rog. no.
- st prog. (one turn on and one turn off per day), nd prog. (identical), rd prog. (identical)
se the " " ey to show in reverse order.
If the st programme is selected, the turn on time is shown.
he display shows: "ON" at
he display shows: "ON" at
he same applies for the turn-off time to be set and for subsequent turning on and off.
Con rm by pressing " " and the wording "SA E " will appear on the display.y.
hen con rming " EE LY RO RA ", you will need to choose the day to which the programming is to apply:
on ; ues; ed; hurs; Fri; Sa; Sat
Once you have chosen the day, use the " " and " " ey and con rm with the " " ey, to programme in the same way as for the
"DAILY RO RA ", choosing whether or not to enable a programme for each day of the wee , and if so choosing number of
interventions and at what times.
Should you ma e an error during programming, you can leave the programme without saving. As you press a ey,
splay will show the word "no SA E".
ress the " " button for two seconds from the radio control and scroll the display instructions with the " " and "-" buttons. You
will come across the message " ser menu" and when you con rm, the message "AD - ELLE and AD -DRA
If we set "Auto-ad ust. ON", the system will automatically ad ust pellet dropping. Alternatively, if we set "Auto-ad ust. OFF," we
can manually correct pellet dropping, varying the range in terms of percentages ( /-
By con rming this function with the menu ey, you can access the function to ad ust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value set, pellet loading increases. his function is useful if
changing the pellet type for which the stove has been calibrated and loading therefore needs correcting.
Should this correction not suf ce, contact the Edil amin-authorised Dealer, to establish the new operating axis.
Flame status may vary depending on the type of pellet used, in addition to normal solid fuel ame variability and regular combu-
stion chamber cleaning carried out automatically by the boiler.
(N.B.: which does NO replace necessary cold suction by the user prior to ignition).
he stove is tted with an electronic function that detects the residual quantity of pellets in the tan .
he detection system is integrated into the electronic board, allowing you to see how many hours and g are left until
pellet exhaustion, at all times. For correct system function, it is important that the following procedure is followed during the rst
ignition (by the Dealer).
INSTRUCTIONS FOR USE
se the " " and " " ey to change the hour. Con rm with the " " ey.
se the " " and " " ey to change the minutes. Con rm with the " " ey.
- 33
%).
-
'
ON/OFF".
, he di-
" will appear.