Best CC34IQSB Manual De Instrucciones página 5

REMOTE CONTROL
The remote control is linked to the hood at the factory.
If, for some reason, the link is lost - follow the directions below:
To Link Remote Control to Hood
1. Turn off hood motor and hood lights.
2. Press on the remote control for at least 3 seconds and release the button. The indicator
light will light up. (Fig. 3)
3. Within 3 seconds - press
approximately 10 seconds to confim that the linking process was successful.
P4
P4
P3
P2
P2 P3
P1
P1
Remote Control Functions (Fig.3)
HOOD
Delay - Off
P1: 5' TIMER function activation/deactivation.
HOOD
hood sensor: AUTOMATIC function activation/
Blower Speed Decrease and Off
P1: 5' TIMER function activation/deactivation.
deactivation.
hood sensor: AUTOMATIC function activation/
P2: Motor off/motor speed decrease.
deactivation.
Blower Speed Increase and On
P3: Motor on/motor speed increase.
P2: Motor off/motor speed decrease.
P4: Lights on/off.
P3: Motor on/motor speed increase.
P4: Lights on/off.
Light
Press (Delay) and
IMPORTANT: Holding
remote and hood to be lost.
CAUTION RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE. DISPOSE
CAUTION RISK OF EXPLOSION IF BATTERY IS
OF USED BATTE TO THE INSTRUCTION.
REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTE TO THE INSTRUCTION.
Battery disposal
When the batteries need to be replaced, dispose of them only and exclusively in the numerous readily available
Battery disposal
special waste bins, especially in shops selling electronic consumer goods. Observance of the regulations on
When the batteries need to be replaced, dispose of them only and exclusively in the numerous readily available
differentiated waste collection, in particular, proper disposal of used batteries, contributes to preventing possible
special waste bins, especially in shops selling electronic consumer goods. Observance of the regulations on
negative effects on the environment and health.
differentiated waste collection, in particular, proper disposal of used batteries, contributes to preventing possible
negative effects on the environment and health.
ƒ
(P2) on the hood control. (Fig. 4) The LED ring will light up for
INDICATOR
LIGHT
As soon as the button is
pressed, the circular crown
As soon as the button is
lights up for 1".
pressed, the circular crown
lights up for 1".
FIG. 3
(Light) together to Reset Filter Alarm.
(Delay) for more than 3 seconds will cause the link between the
P2
HOOD
CONTROL
LINKING procedure
- To unambiguously associate the radio control with
LINKING procedure
the hood, you can activate a LINKING procedure.
¤
- To unambiguously associate the radio control with
Once the procedure has terminated, the radio
the hood, you can activate a LINKING procedure.
control functions only and exclusively with the
Once the procedure has terminated, the radio
associated product.
control functions only and exclusively with the
- This procedure is useful if there are two or more
associated product.
products that can be controlled by means of radio
-
(P5)
- This procedure is useful if there are two or more
control, for example, in apartments with adjacent
products that can be controlled by means of radio (P3)
kitchens, showrooms, fairs, etc.
control, for example, in apartments with adjacent
1 - Turn off the hood motor and the lights
kitchens, showrooms, fairs, etc.
2 - Press P1 for 3": the circular crown will light up
ƒ
1 - Turn off the hood motor and the lights
3 - Confirm the link to the hood within 3" by pressing
2 - Press P1 for 3": the circular crown will light up
the button indicated on the next page.
3 - Confirm the link to the hood within 3" by pressing
the button indicated on the next page.
See "Controls" section on previous page for
more information on each function.
P1
P3
P1
P2
P3
P2
As soon as the button is
pressed, the circular crown
lights up for 1".
P4
P3
P1
- 5 -
(P1)
(P4)
+
L1
(P2)
LED
RING
FIG. 4
Confirm P2
P5
Confirm P2
P5
P4
P4
LINKING procedure
- To unambiguously associa
- This procedure is useful if
1 - Turn off the hood motor
2 - Press P1 for 3": the circ
3 - Confirm the link to the h
P1: Activate/deact
P2: Filter change i
P3: Decreases fan
P4: Turns fan moto
P5: Turns lights on
L1: LED Indicator
- Hood in stand
the last key ha
- Motor on: L1 li
freque
- 10' TIMER fun
- Filter alarm ac
the hood, you can activate
Once the procedure has te
control functions only and
associated product.
products that can be contr
control, for example, in ap
kitchens, showrooms, fair
the button indicated on