Motor - Technical Data; Charging The Battery; Motor; Calibrating The Actuators - Etac Swift Mobile Manual Del Usuario

Motor - Technical data

Operation voltage:
Current:
Battery type:
Charger in:
Charge time:
Swift Mobil Tilt Motor protection class:
Charger protection class:

Charging the battery

The product must be dry and in a dry environment when
managing the battery.
J1. Take the battery out of the control box and place it in the C3
charger.
When the battery is located in the charger the green light starts
to flash until it is fully charged, at which time the light remains
constantly green.
Charging the battery
• The battery must be charged fully before the product is used for
the first time.
• When starting to use the product the battery must be charged
once a day or more frequently if necessary.
• When the product is not in use for a prolonged period the bat-
tery must be charged once a month.
• When fitting the battery make sure that the contact surfaces in
the battery and control box are clean and dry. If a beep is heard
the battery is fitted correctly and the chair is ready for use. If
there are two buzzing sounds followed by one beep, the control
box is in calibration mode and calibration must be completed
before further use.
• If the battery is hot after a charge or the chair is overloaded
when in use, the battery's overheating protection may be trig-
gered. Remove the battery and allow it to cool down for about
30 minutes.
• If the battery is taken out of the control box, wait at least one
minute before fitting a new battery.
• It is not permitted to use the chair without a battery in the
control box.

Motor

K1. Handset (Protection against water in line with IP 65), included.
K2. Charger, included
K3. Actuator (Protection against water in line with IP 66)
K4. Battery (Protection against water in line with IP 65)
K5. Control unit (Protection against water in line with IP 65)
Make sure the battery, actuator and the handset are connected
properly to the control unit.

Calibrating the actuators

L1. Both the up and down buttons are pressed simultaneously
until a beep followed by two buzzing sounds is heard (about
10-15 seconds). The control box is now in calibration mode.
L2. Calibration is carried out by holding the back button in until
both actuators stop in the end position. Keep the button
pressed in for an extra couple of seconds. The chair is now
calibrated and can be used.
English

Fault-finding chart

24 V
Faults
7A
A signal is heard
NiMH
when using
110 or 240 V AC
chair
5-8 h
If tilting does
IP 65
not work
IP 65
If tilting does
See Figure J
not work
If tilting does
not work

Accessories

M1.
M2.
M3.
M4.
M5.
M6.
M7.
M8.
M9.
M10. Seat cover
M11. Anti-tip stabilisers including bracket
M12. Anti-tip stabilisers excluding bracket
M13. Crossbar 605 mm
M14. Chest belt
M15. Positioning belt
M16. Hemiplegic armrest
M17. Armrest lock
M18. Angle adj. footrest
M19. Soft back pad
See Figure K
M20. Tilter
M21. Widening kit
M22. Soft Comfort seat
M23. Soft Comfort seat - narrow opening
M24. Comfort padding
M25. Trunk support
M26. Armrest cushion, pair
M27. ROHO pressure-relieving cushion
See Figure L
M28. Pan
M29. Lid with handle
M30. Amputee legrest
M31. Soft cushion - standard opening
M32. Soft cushion - oval opening
17
Etac / Swift Mobile Tilt Motor / www.etac.com
Possible cause
The battery is almost
flat
The cables may not
be connected or the
battery is flat.
The actuators
may need to be
calibrated.
The battery is
overheated.
Leg and calf rest, angle-variable
Footrest
Commode pan
Pan-holder attachments
Attachments for low pan-holder mounting
Commode pan holders
Bucket holders
Splash guard
Comfort seat
Solution
Charge the battery
Insert the cables,
charge the battery.
Calibrate the
actuators.
Remove the battery
and allow it to cool
down for at least
30 minutes.
See Figure M