OBJ_BUCH-911-009.book Page 18 Thursday, October 23, 2014 10:52 AM
18 | English
To achieve optimum extraction results, please observe the
following notes:
– Pay attention that the extraction device faces flush against
the workpiece or the wall. This also makes drilling at a right
angle easier.
– When using the extraction device, always work with the
maximum speed.
– After reaching the desired drilling depth, pull the drill bit
out of the drill hole first and then switch off the impact drill.
– Use the extraction device only with the filter element 17
mounted, as otherwise dust/chips could access the interi-
or of the power tool and cause damage.
– Check the condition of the filter element 17 regularly. Re-
place a damaged filter element immediately.
– The dust protection ring 19 can wear, especially when
working with large drill-bit diameters. Replace the dust
protection ring when worn/damaged.
Mounting the Extraction Device (see figure A)
Guide the extraction device 11 from the front toward the bot-
tom side of the impact drill. Pay attention that the extraction
device 11 faces flush against the casing and that it is locked.
Cleaning the Extraction Device (see figures B–D)
The dust collector 12 is sufficient for approx. 10 drillings with
a drilling diameter of 10 mm.
When the extraction force diminishes or when the level indi-
cator 13 is full, the dust collector 12 must be emptied. For
this, press on the riffled surface of the release button 16 and
take off the dust collector 12.
Empty and clean the dust collector 12. Clean the filter ele-
ment 17 by gently striking or tapping against it.
Check the filter element 17 for damage and replace it as re-
quired.
Press on the holder of the filter element 17 and pull it out. Re-
place the filter element 17 including the holder. When placing
on the holder again, make sure that the rubber gasket 18 is in-
serted.
Reattach the dust collector 12 again and lock it by pressing
against the smooth surface of the release button 16.
Removing the Extraction Device (see figure E)
For disassembly of the extraction device 11, press release
button 20 and pull off the extraction device 11 toward the
front.
1 609 92A 0TN | (23.10.14)
Stowing the Extraction Device (see figure F)
For stowing the extraction device 11 in the case, remove the
extraction device 11, slide it together and attach clamp 21.
Attach the locking latch 22 or empty the dust collector 12 be-
fore placing down the extraction device.
Auxiliary Handle
Operate your machine only with the auxiliary handle 9.
Before any work, make sure that the wing bolt 10 is
firmly tightened. Loss of control can cause personal inju-
ry.
The auxiliary handle 9 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 10 in
anticlockwise direction and set the auxiliary handle 9 to the
required position. Then tighten the wing bolt 10 again in
clockwise direction.
Adjusting the Drilling Depth (see figure G)
The required drilling depth X can be set with the depth stop 1.
Press the button for the depth stop adjustment 3 and insert
the depth stop into the auxiliary handle 9.
The knurled surface of the depth stop 1 must face downward.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Changing the Tool
Keyless Chuck (PSB 750 RCE/PSB 7500 RCE/
PSB 750 RCA) (see figure H)
The drill spindle is locked when the On/Off switch 8 is not
pressed. This makes quick, convenient and easy changing of
the tool in the drill chuck possible.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 2 by hand in ro-
tation direction until the locking action ("click") is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Keyless Chuck (PSB 650 RE/PSB 680 RE/
PSB 6500 RE/PSB 6200 RE/PSB 650 RA) (see figure I)
Press the spindle lock button 25 only when the ma-
chine is at a standstill.
The drill spindle is locked by pressing the spindle lock button
25. This makes quick and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 2 by hand in ro-
tation direction until the locking action ("click") is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Bosch Power Tools