Tabla de contenido
Publicidad
The booster pump may be installed anywhere near the machine
approaching the water piping and corresponding 3/4" cock to the devi-
ce. Ensure that the water cock is still accessible.
Connect one end of the booster pump to the water cock and the other
end to the hose using the thread mouthpiece of the machine.
Electric installation
Before proceeding with the installation of the machine, check the follo-
wing:
1.-The voltage of the machine should coincide with the mains voltage.
These machines are supplied for 230 or 400 V, prepared for 400 V.
2.-Install a switch with fuses 25A (LV-900, E-1000 and LV-1100) or 35A
(LV-1200). The machine is equipped with a cable with a cross section
of 5x4 mm² (LV-900, E-1000 and LV-1100) or 5x6 mm² (LV-1200) and
a length of 1,70 m. They must be earthed.
OPERATION
Starting
1.-Open the 3/4" stopcock to allow water to enter the machine.
2.-Turn on the switch. Turn on the booster pump if one has been incor-
porated to the machine.
3.-Check and make sure that the aspiration filter and the drain plug are
correctly positioned.
LV-1200
Switch
Rinse aid
container
Amber lamp
Red lamp
Main Switch
Green lamp
Rinse
aid doser
Booster pump
4.-Turn the switch control to the ON position for the automatic filling of
the wash tank and the connection of the heat elements.
5.-The lighting up of the green lamp indicates the machine has rea-
ched the optimum temperature. Now introduce the detergent into the
tank:
-LV-900. Approximately 1 full coffee cup at the beginning of the cycle
and 1/2 a cup every 5 cycles.
-E-1000, LV-1100 and LV-1200. Approximately 2 full coffee cups at the
beginning of the cycle and 1 cup every 5 cycles.
6.-Remove the solid residues from the plates and place them in the
baskets. Select the washing programme by turning the timer control
clockwise.
LV-1100 and LV-1200: Hood actuated 1, 2 or 3 min cycle.
Important: Check that the rinsing aid container is filled up. By turning
the timer, 7 or 8 impulses, we will see the filling of the rinsing aid tube
and its going into the boiler. The doser adjustment is made by means
of an adjusting screw.
LV-1200. If the motorpump direction of rotation us wrong, to reverse
the direction of rotation, by interchanging two of three phase wires in
the electrical installation.
Tank cleaning
The tank should be cleaned after every washing process:
-Open the door and pull out the drain plug without lifting the filters, in
order to empty the tank and to prevent any large particles from ente-
ring the suction passage of the motor-pump. (Never remove the aspi-
ration filter when the tank is dirty).
-Extract the top filter and clean it carefully.
-To clean the interior of the wash tank, close the door and start the
Pressure
machine (after having previously removed the drain plug). In this way,
reducer
water will enter via the rinsing dispersers and the machine will clean
itself. This operation should be carried out for 2 to 3 minutes and will
leave the interior of the machine in an almost completely clean condi-
Water softener
tion.
-Now clean the walls and the interior of the tank in a thorough manner.
The outside of the machine MUST NOT BE washed under a direct
water jet; instead you can use a wet cloth and any ordinary detergent.
-Before cleaning, overhauling or repairing the machine, it is necessary
to unplug it from the mains.
-In the event the power supply cable should get damaged and have to
be replaced, the repair may only be done by a SAMMIC approved
assistance service.
-The emission noise level measured on a typical machine is inferior to
70 dB (A) at a distance of 1 m.
5
OTHER IMPORTANT
REMARKS
Publicidad
Tabla de contenido
