Installing An Optical Radio Safety Edge Or Resistive Safety Edge With Xse Transmitter; Installing The Optical Radio Or Resistive Safety Edge And Its Xse Transmitter; Installing A Base Magnet On The Door Runner; Programming The Xse Transmitter - SOMFY Home Motion ROLLIXO RTS Manual De Instalación

1 2 3 4
1 2 3 4
Prog
STOP
Rollixo RTS
STOP Prog
1 2 3 4
[5]. Press the motor's upper end limit push-button.
Prog
STOP
or
[6]. Press button to position the garage door in the low position.
Adjust the bottom position with buttons
1 2 3 4
Prog
STOP
1 2 3 4
1 2 3 4
STOP Prog
Prog
STOP
[7]. Press the motor's low end limit push-button.
or
[8]. Press simultaneously on the
1 2 3 4
until the motor's up and down movement occurs to enter motor adjustment
Prog
STOP
mode.
Indicator light 1 goes out.
1 1 2 2 3 3 4 4
Prog
STOP
STOP Prog
1 2 3 4
Prog
STOP
or
1 2 3 4
STOP Prog
4 - instaLLinG an oPtiCaL raDio
safety eDGe or resistive safety
eDGe With Xse transMitter
4.1 installing the optical radio or resistive safety edge
and its Xse transmitter
Follow the instructions provided with the XSE transmitter and the optical or
resistive safety edge installation kit.

4.2 installing a base magnet on the door runner

Base
magnet
6
and .
and buttons or press on the
1 2 3 4
Prog
Prog
STOP
1 1 2 3 2 3 4 4
Prog
STOP
STOP Prog
A base magnet must be fitted
for a resistive safety edge.
This is recommended for an
optical safety edge in order to:
- extend the battery life
- eliminate the risk of ground
detection, to secure
closing of the door
- automatically activate
maximum level of sensitivity of
the movement sensor
- increase the sensor operating
time by 25 to 35 seconds when
the base magnet is detected.
STOP
[1]. Press button to position the garage door in the low position.
1 2 3
STOP
[2]. Attach the base magnet to the edge of the runner, positioning it in line
with the transmitter.
1 2 3
STOP
This operation is important. Ensure the dimensions are observed.
button

4.3 Programming the Xse transmitter

[1]. Press the button on the receiver until the indicator light comes on
Prog
permanently.
[2]. Using the tip of a pen, press the transmitter PROG push-button for 4
seconds.
Indicator light 2
indicator light will flash and then go out (this may take a few seconds,
the time required for the transmitter and receiver to communicate with
each other).
The transmitter is memorised in the receiver.
1 2 3
STOP
4 s
1 2 3
STOP
5 - instaLLinG an oPtiCaL raDio
safety eDGe With ose transMitter
the
5.1 installing the optical safety edge and its ose
transmitter
the
Follow the instructions provided with the OSE transmitter and the optical safety
edge installation kit.

5.2 Programming the ose transmitter

[1]. Press the button on the receiver until the indicator light comes on
Prog
permanently.
[2]. Using the tip of a pen, press the transmitter PROG push-button for 4
seconds.
Prog
4
Prog
4
Prog
10 mm maxi.
on the receiver goes out and the receiver Prog
4 1
Prog
STOP
4 1
Prog
STOP
Copyright © 2014 Somfy SAS. All rights reserved.
STOP
Base
magnet
2 3 4
Prog
2 3 4
Prog