Patient Messages; Reminders; Notifications; Travel Information - DeVilbiss Healthcare SleepCube AutoAdjust CPAP DV54 Serie Guía De Instrucciones

patiEnt mESSagES/traVEl/Dc opEration

PaTienT messaGes

Your SleepCube will alert you of issues that may require some action on your part in order to make your therapy more effective. These messages
are displayed when the device is turned on, either by pressing the ON/OFF button or by breathing into the mask. You can press any key or button
to clear the message from the display, but the SleepCube will operate normally even if the message is not cleared.
Two kinds of messages are displayed: Reminders and Notifications.

Reminders

Reminders alert you when parts of your system need to be replaced. Some components of your system wear over time and, if not replaced, may
compromise your therapy. If you see a message on the display that is not listed below, you may have the optional DeVilbiss SmartLink™ Module
attached to your device, which provides additional messages. Refer to the documentation that was provided with the SmartLink Module.
Clean Filter – The filter should be checked every 10 days for signs of dirt or wear so that it can be cleaned as needed.
This message helps to remind you to check it regularly.

Notifications

Notifications identify conditions in your SleepCube that may require action by you or your home care provider in order to maintain a high level of
therapy. If you see a message on the display that is not listed below, you may have the optional DeVilbiss SmartLink Module attached to your device,
which provides additional messages. Refer to the documentation that was provided with the SmartLink Module.
NOTE
-The values displayed are examples only.
Delay Running xx Minutes Left – While a comfort delay session is active, this message is flashed on the display every 5
seconds to let you know how much time is left in the delay.
Mask Leak – This message means the SleepCube has detected a large amount of airflow during therapy for at least 10% of
the time during your previous use session. This notification is displayed when the device is turned on. If this message is
displayed, put on the mask and adjust the headgear to ensure the mask is properly fitted to your face. Follow the mask
manufacturer's directions for adjusting the mask and headgear for proper fitting. Available on AutoAdjust models.
Mask Off – This message appears whenever a high airflow condition occurs. High airflow is normally due to a poor mask
fit or a removed mask. Check for leak around the mask seal and make adjustments as necessary according to the mask
manufacturer's instructions. This message will be displayed until the high airflow problem is corrected. If the high airflow
condition persists for about 20 seconds, the device will automatically turn off (if AutoOFF is enabled).
Device Fault – If a device fault message is displayed, refer to Troubleshooting for instructions.
sleePCUbe TRaVel infoRmaTion
International Power Changes
Your DeVilbiss SleepCube is equipped with a universal power supply. This means that it is automatically capable of accepting line voltages of 100 to
240V~ 50/60Hz. You do not need to make any adjustments to the device if you are traveling to another country where the line voltage is different
than your domestic line voltage. Simply contact your home care provider for the correct style power cord for the region in which you will be
traveling (refer to Accessories/Replacement Items for the correct part number).
Altitude
Your SleepCube automatically compensates for changes in altitude between sea level and 9000 ft (2750 m). You do not need to make adjustments
to the device for changes in altitude.

sleePCUbe DC oPeRaTion

Battery Power

Your SleepCube can be operated from a 12V DC power source in a motor home, boat or other recreational vehicle. The power source can be
used with a 12V DC accessory cable or a 12 V DC stand-alone battery. Both parts are available from your home care provider (refer to
Accessories/Replacement Items for the correct part numbers). Both accessory cables are required for stand-alone battery operation. The stand-
alone battery connection uses clamps that attach to the terminal connections of the battery.
EN
Clean Filter
Delay Running
10 Minutes Left
Mask leak =
25 % Check Fit.
Mask Off. Please
check mask fit.
Device Fault E07
Call Provider
SE-DV54
11