Cleaning & Maintenance - Balanced Body Allegro Manual Del Usuario

INSTALL THE RISERS
Remove locking pins from the
frame. Insert the risers through
the holes on the Allegro
frame. Turn the risers until the
attached pulleys point toward
the footbar and are angled
outward. See Figure E.
Reinsert locking pins.
ATTACH THE ROPES
6. To attach the ropes, first engage at least one spring from the
carriage to the springbar to keep the carriage home. Unroll
the ropes and separate them.
7. Clip a cotton loop onto the end of the each rope and hang
the loops on the shoulder rests. Thread the other end of each
rope through a pulley and back into the cam cleats on the
carriage to adjust the length. Be sure to go through the chrome
eyestraps on both sides of the cam cleats. Always push the
rope firmly down into the cleats to ensure a good grip.
STORING THE ALLEGRO REFORMER
Stacking
To see a demonstration of how to stack the Allegro, watch the
Setup and Safety portion of the Allegro Introductory/Level 1 DVD.
Attach the springs to keep the carriage from moving. Move the
footbar to the "down" position. Remove the shoulder rests and
store in the slots at the head of the frame. Put the head rest
down. Remove the risers and store in the holes at the head end
of the frame. Place the ropes and loops inside the Allegro frame.
After the first machine is in position, put the spacer blocks in
place before stacking the next machine.
Standing
It is absolutely critical that
the Allegro footbar be set and
locked in the correct position
for standing storage. Move
and lock the footbar into the
position closest to the foot-end
of the Reformer frame. Raise
the footbar to its highest
position. Lift the head-end
of the Allegro frame to waist
height. Then raise the frame
to vertical. Use your foot to
steady the wheeled end of the
frame as you lift to vertical.
The vertical Allegro will come
to rest on the footbar and the
transport wheels.
Locking Pin
Fig E
Fig F
CLEANING & MAINTENANCE
Cleaning
Wipe the carriage pad, headrest, footbar and shoulder rests with
a soft cloth and a mild, non-abrasive cleaner after each use. Keep
the carriage track and wheels clean from dust and dirt. Wipe the
entire track with a towel and cleaner regularly. Clean the footbar
trunnion track weekly. Clean the frame with a mild, non-abrasive
cleaner. Keep the ropes and springs clear of dust. Cotton loops
can be machine-washed. Hang to dry.
Lubrication
The Allegro carriage rail or C-channels may be lubricated with dry
silicon spray only. First, clean the C-channel, then spray a clean,
dry rag with dry silicon spray and wipe the C-channel thoroughly.
The foot bar trunnion C-channel can be lubricated the same way.
The lever spring and pin (see figure D) can be lubricated every
month with common household oil. Apply a couple drops of oil to
the lever spring and to the area where the pin enters the foot bar
then compress and release the spring lever a few times. Wipe off
any excess oil.
A squeaking noise from the riser pulleys or built-in standing
platform hinge may indicate a need for lubrication. To lubricate
riser pulleys; first remove the ropes from the riser pulleys. Place
one or 2 drops of oil on the swivel portion and the axel of the
pulley wheel. Swivel the pulley a few times and spin the pulley
wheel to allow the oil to work then wipe off excess oil and
rethread the ropes.
To lubricate the built in standing platform hinge: Place a few
drops of oil along the length of the standing platform hinge
where the two pieces of hinge join together. Open and close the
standing platform to allow the oil to work. Wipe off all excess oil.
MAINTENANCE
» Depending on frequency of use, the springs should be safe to
use for one to two years (3000 hours). Replace any spring that
is kinked, bent or shows separations while at rest.
» Remove hair and debris from the axles of the wheels. Debris
can create pressure on the bearings, causing them to wear. If
you hear noise from the bearings, replace them. Otherwise, no
maintenance on the bearings is required
» Repair any tears in the upholstery with an upholstery repair kit
available at auto parts stores, or have the repair done locally.
Call Balanced Body for other upholstery and re-upholstery
options.
» Replace any missing screws, retention pins, or other parts.
QUESTIONS?
Call 1-800-PILATES (1-800-745-2837) in the US. +1- 916-388-
2838 (International)
13