Balanced Body Allegro Manual Del Usuario página 9

Then re-insert the T-pin. Make sure the bushings on the PTB
(where the T-pins are inserted in to the PTB) are clean.
Push-Through Bar (PTB) T-pin
setting. For bottom-sprung
exercises, if your client's head
is below the PTB, use the T-pin
setting in addition to the
safety strap or chain. Spotting
your client is highly
recommended. This is
important for safety.
Correct safety strap
attachment. For bottom-
sprung exercises, the safety
strap or chain should always
secure the bar.
The safety strap or chain should wrap around the PTB and the
canopy frame, not the eyebolts. The strap or chain is only as
strong as the weakest link, and the frame and bar are a great
deal stronger than eyebolts. Figure 6.
Seting the PTB for bottom-sprung exercises. For bottom-
sprung exercises, the safety strap should be attached so that the
angle of the push-through bar is at no lower than the 4 o'clock
position. This limits the range of the bar and prevents it from
potentially coming into contact with the user.
CHAIRS
Dismount with control. When dismounting the chair, release the
pedals slowly, with control. Don't let the pedal snap back.
Spot users. When a user is standing, sitting or lying on top of
the chair, there is increased risk of falling. Standing exercises,
in particular, can be unstable. Spotting users will make these
exercises safer.
Hourglass spring mounts. If your chair
has hourglass spring mounts and the
mounts do not successfully retain the
springs, replace the fiber washers (they
are reddish-brown in color). Figure 7. If
your chair is a Balanced Body Split-step
Pedal Chair (Combo Chair), please
consider upgrading to the Cactus
Springtree).
Figure 6: Safety strap holding the
push-through bar at 4 o'clock. The strap is
secured to the PTB and canopy frame, not
the eyebolts.
Figure 7: Fiber washer
UPHOLSTERY CLEANING & MAINTENANCE
Cleaning. You can extend the life of upholstery by keeping it
clean and free of dirt, oil and perspiration. After each use, wipe
down the upholstery with a solution of mild soap and water. Then
wipe it down with clean water and dry with a soft towel.
Disinfecting. Equipment upholstery is coated with BeautyGard®,
which offers antibacterial protection. If you want additional
disinfection, use any off-the-shelf disinfectant spray or solution,
such as Pine Sol or Lysol . Since disinfectants will leave a
® ®
fragrance residue buildup with repeated use, we recommend
wiping down the disinfected area with clean water using a sponge
or soft towel.
HOW TO INSPECT AND TIGHTEN NUTS AND BOLTS.
Use your fingers to check nuts and bolts
for tightness. If you can turn the nut or
bolt with your fingers, it's too loose and
should be tightened. To tighten, first
tighten using your fingers. Rotate nuts
and bolts clockwise to tighten. Then use
a small wrench to tighten further. Insert
a screwdriver through eyebolts to hold
them steady while you tighten the nuts.
Use your forefinger and middle finger on
the handle of the wrench to tighten, (as
opposed to using your entire hand).
This technique will help prevent over tightening, which can
damage metal parts. Figure 8.
EQUIPMENT INSPECTION AND MAINTENANCE LOG
We suggest that you keep a maintenance log for each piece of
equipment. The log should include:
1. A description of the machine including the serial number, the
date and place of purchase, and the manufacturer. All of this
information should appear on the invoice.
2. Date and description of all required maintenance and
inspections performed.
3. Date and description of each repair, including name and
contact information for person or company performing the
repair.
Figure 8: Use two fingers to
tighten bolts
9