Shutdown; Maintenance And Care - Windsor Radius 30 Manual Del Usuario

1 Tie-down area above the pushing han-
dle
2 Tie-down area under the device hood
Note
– Observe markings for fixing points on
base frame (chain symbols).
– Do not kink the bowden or sheathed ca-
bles.

Shutdown

If the sweeper is going to be out of service
for a longer time period, observe the follow-
ing points:
Park the sweeper on an even surface.
Switch off engine.
Turn the main switch using "0" position
and pull it out.
Lock parking brake.
Lock the sweeper to ensure that it does
not roll off.
Raise roller brush. Thus, engage both
adjustment levers in the top boring.
The side-brushes lift up.
Clean the inside and outside of the
sweeper.
Park the machine in a safe and dry
place.
Disconnect batteries.
Charge batteries and recharge approx.
every 2 months.

Maintenance and care

General notes
– Maintenance work may only be carried
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
– Mobile appliances used for commercial
purposes aer subject to safety inspec-
tions according to VDE 0701.
Cleaning
Warning
Risk of damage! Do not clean the appliance
with a water hose or high-pressure water
jet (danger of short circuits or other dam-
age).
Cleaning the inside of the machine
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
Open the device hood.
Clean machine with a cloth.
Blow through machine with com-
pressed air.
Close cover.
External cleaning of the appliance
Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Note
Do not use aggressive cleaning agents.
Maintenance intervals
Maintenance by the customer
Daily maintenance:
Check the sweeping roller and the side
brush for wear and wrapped belts.
Check function of all operator control el-
ements.
Check functioning of all indicator lamps.
Weekly maintenance:
Check tension, wear and tear and func-
tioning of the drive belts.
Check the smooth running of the brush
cables and the moveable parts
Check the gasket in the sweeping area
for position and wear.
Check the sweeping track of the sweep-
ing roller.
Clean the dust filter.
Note
For description, see section on Care and
maintenance.
Note
Where maintenance is carried out by the
customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialized Wind-
sor dealer may be contacted at any time.
Maintenance by Customer Service
Maintenance to be carried out after 20 op-
erating hours:
Carry out initial inspection.
Maintenance to be carried out every 100
operating hours
Maintenance to be carried out every 300
operating hours
Maintenance to be carried out every 500
operating hours
Note
In order to safeguard warranty claims, all
service and maintenance work during the
warranty period must be carried out by the
authorized Windsor Customer Service in
accordance with the maintenance booklet.
Maintenance Works
Preparation:
Park the sweeper on an even surface.
Turn the main switch using "0" position
and pull it out.
Lock parking brake.
General notes on safety
Danger
Risk of injury!
The engine requires approx. 3-4 seconds
to come to a standstill once it has been
switched off. During this time, stay well
clear of the working area.
– Pull out the battery plug or clamp the
batteries while working on the electrical
unit.
– Allow the machine sufficient time to cool
down before carrying out any mainte-
nance and repair work.
– Do not touch any hot parts, such as the
drive motor.
Note
Remove the waste container and move the
pushing handle to the front prior to tilting
the appliance. Do not rest the appliance on
the pushing handle.
Switch off the appliance prior to clean-
ing and performing any maintenance
tasks or replacing parts.
Adjust the Bowden cable of the acceler-
ation drive
This must be adjusted if the drive perfor-
mance of the appliance becomes insuffi-
cient when driving uphill.
Loosen counter-nut.
Adjust the adjustment screw.
Tighten the counter-nut.
Checking roller brush
Lock parking brake.
Remove the waste container.
Remove belts or cords from roller
brush.
Replacing roller brush
Replacement is due if a visible deteriora-
tion in sweeping performance caused by
bristle wear is evident.
Note
Remove the waste container and move the
pushing handle to the front prior to tilting
the appliance. Do not rest the appliance on
the pushing handle.
Lock parking brake.
Remove the waste container.
Tilt the appliance rearward.
Lift the waste flap, press in the bearing
cap and swivel the roller brush toward
the front.
Pull out roller brush.
11
English