Wiring/Configuration Nema 4 - Franklin Electric SubDrive75 Guía De Instalación Rápida

Wiring /Configuration-NEMA 4
SubDrive75, SubDrive100, SubDrive150, MonoDrive & MonoDriveXT
To operate a different pump size, a Configuration Switch (SW1) must be positioned to select the correct pump rating .
Reference the chart below for appropriate Configuration Switch setting .
Feed the 230 V power leads through
the large enclosure opening and
securely attach to the terminals
marked L1, GND and L2.
Configuration Switch SW1
MonoDrive MonoDriveXT
1/2 hp (motor) 1 .5 hp (motor)*
MonoDrive MonoDriveXT
3/4 hp (motor)*
MonoDrive MonoDriveXT
1 hp (motor) 2 hp (motor)
*(default)
O
N
1 2 3
O
N
1 2 3
Sensor Connection
PRESSURE
SENSOR
Red Blk
TO
INPUT
FILTER
From Power Source
RV1
RV2
J1
L1 L2
J1
(INPUT)
L1 L2
(Input)
From Power Source
Power Supply
From Circuit Breaker
Feed the pressure sensor wires
through the small enclosure opening
and securely attach to the sensor
terminals.
Feed the 230 V power leads through
the large enclosure opening and
securely attach to the terminals
marked L1, GND and L2.
SubDrive75
3/4 hp (pump)*
SubDrive75
N/A 1 hp (pump)
SubDrive75
1 .5 hp (pump)
#3 Switch
Underload sensitivity selection
OFF Position - Normal(default)
4
See SubDrive/MonoDrive Installation Manual for more information .
#4 Switch
Steady Flow - Control selection
OFF Position - Standard(default)
See SubDrive/MonoDrive Installation Manual for more information .
4
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or access cover for
more information.
TO
OUTPUT
FILTER
J2
R1 1 2 3 4 1 2 3 4
PRESSURE SENSOR FAN
ADJUST SW1 SW2
GND
Sensor Connection RED YEL BLK
(BRN) (BLU)
(OUTPUT)
PRESSURE
SENSOR
PRESSURE
SENSOR
Red Blk
L1 L2
J1
(INPUT)
Feed the motor leads through
the large enclosure opening and
L1 L2
securely attach to the terminals
(Input)
matching the lead colors to the
colors shown.
Power Supply
From Circuit Breaker
Feed the pressure sensor wires
through the small enclosure opening
and securely attach to the sensor
terminals.
SubDrive100 SubDrive150
1 hp (pump)* 1 .5 hp (pump)*
SubDrive100 SubDrive150
1 .5 hp (pump) 2 hp (pump)
SubDrive100 SubDrive150
2 hp (pump) 3 hp (pump)
ON Position - Low
ON Position - Steady Flow
Configuration Switch SW1
Output to Motor
Configuration Switch SW1
J2
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or access cover for
Red Yel Blk
more information.
(Brn) (Blue) (Blk)
(Output)
Output to Motor
J2
RED YEL BLK
(BRN) (BLU)
(OUTPUT)
PRESSURE Red Yel Blk
SENSOR
(Brn) (Blue) (Blk)
(Output)
Feed the motor leads through
the large enclosure opening and
securely attach to the terminals
matching the lead colors to the
colors shown.
O
N
O
1 2 3 4
N
O
1 2
N
O
N
1 2 3 4
1 2
O
N
O
N
1 2 3 4
1 2
3 4
3 4
3 4
9