Connection And Start Up; Declaration Of Conformity - V2 PROG2-USB Manual De Instrucciones

CONNECTION AND START UP

PROG2-USB can work while linked up to a computer
only if WinPPcl 4.0 (or later versions) has been installed
with relative driver.
Carefully follow the instructions given in the QUICK GUIDE
TO SOFTWARE AND DRIVER INSTALLATION.
DO NOT CONNECT THE PROG2-USB TO THE PC BEFORE
INSTALLING THE DRIVERS!
Once the driver installation is complete, you can use the PROG2-
USB for programming via WinPPcl.
In order to use the PROG2-USB without the aid of a PC, you will
have to insert 4 batteries in the back of the container then turn
on the POWER switch at the front.
The screen displays for 2 seconds approximately:
PROG2
Then, for 2 seconds, the contract number and the "SERIAL
NUMBER" access code appear on the screen: (Example)
CONTRATTO:
S.N.:
Soon after that, the screen displays:
ITALIANO
Acting on keys it is possible to select 4 different
languages: ITALIAN, ENGLISH, FRENCH and SPANISH.
Press to confirm: the selected language is not stored, it is
necessary to select it every time you switch the device on. The
screen displays:
ROYAL PLUS
TX MENU
Acting on keys it is possible to select the following menus:
1. ROYAL PLUS TX MENU
It permits to:
• Read the dip-switches code of each single key of a PLUS TX.
• Read PLUS TX features and create a duplicate.
• Set up the desired dip-switches code by keyboard.
2. PERSONAL PASS TX MENU
It permits to:
• Read a transmitter label code and create a duplicate.
• Set up by keyboard the label code and store it in a
programmable TX.
• Generate a random code and store it in a virgin transmitter.
3. MEM MODULE CODIFIER MENU
It permits to:
• Read MEM module memory zones, delete the desired zones or
change their content.
• Duplicate a MEM module.
• Delete completely a MEM module.
• Enable and disable Passe-Partout function
V2
VER 3.66
0215
0000
4. RX CODIFIER MENU
It permits to:
• Read the memory zones of a RECEIVER module.
• Delete desired memory zones or change their content.
• Duplicate the content of a receiver.
• Delete completely the memory of a RECEIVER module.
• Enable and disable Passe-Partout function
• Enable and disable PASSWORD function
AVAILABLE CONNECTORS
: allows for the PROG2-USB to be connected to a
Personal Computer via USB cable
FASTPROG: allows for the PROG2-USB to be connected to a
FASTPROG programmer via RJ45 cable
TX CONNECTOR: allows for the insertion of devices fitted with
special CARD EDGE connection (e.g. remote controls, receivers
etc..) for the programming.
MEM SOURCE: allows for the insertion of memory modules for
programming or deleting.
MEM TARGET: allows for the insertion of a vacuum memory
module to duplicate the content of another module inserted in
the MEM SOURCE container.
WARNINGS
Before inserting the device to programme into the appropriate TX
connector of PROG2, make sure that it is not fed.
Programmable devices, transmitters excluded, before the
programming through PROG2 must be initialised with a contract.
Just store a transmitter of the desired contract before the
programming.

DECLARATION OF CONFORMITY

V2 S.p.A. hereby declare that PROG2-USB equipment conforms
to the essential requirements established in the electromagnetic
compatibility directives:
93/68/CEE electromagnetic compatibility
73/23/EEC electrical safety
99/5/EEC directive radio
and that the following technical standards have been applied
EN 301 489-3
EN 301 489-1
EN 300 220-3
EN 300 220-1
EN 60 950 (92)
Racconigi, 9 July 2007
Legal representative, V2 S.p.A.
A. Livio Costamagna
14