Product Description - 3M DBI SALA 6100562 Manual Del Usuario

;
Prior to installation and use of this equipment, record the product identification information from the ID label in the
Inspection and Maintenance Log (Table 2) at the back of this manual.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA™ Ladder Anchor. The Ladder Anchor is a single point anchorage connector for a personal
fall arrest system designed to be attached to a fixed metal ladder on a structure.
Figure 2 illustrates components of the Ladder Anchor. See Table 1 for Component Specifications. The Ladder Anchor is
comprised of the Anchor Weldment (A), which serves as the body of the Ladder Anchor. The Ladder Fasten Points (B) enable the
Ladder Anchor to be secured to a ladder with the applicable hardware kit. The Tube Cap (C) keeps water out of the Weldment
and the Connection Eye (D) enables connection of a Self Retracting Device (SRD) to the Ladder Anchor. The Bolt Cap (E), Rung
Hook (F), U-Bolt (G), Bolt (H), Hex Nut (I), Collar Bracket (J), and Washer (K) are all included as part of the hardware kit, in
varying quantities based upon the hardware kit one may have. The Tagline (L) enables quick and easy retrieval of the SRD cable.
System Specifications:
Capacity:
Anchorage:
Service Temperature:
Minimum Breaking Strength: 2,700 lbs (12 kN)
SRD Maximum
Arresting Force:
Dimensions:
Weight:
Standards:
Component Specifications:
Figure 2
Reference Component
A Anchor Weldment
Ladder
B
Fasten Points
C Tube Cap
D Connection Eye
E Bolt Cap
F Rung Hook
Ladder Specifications:
Rung Spacing:
Rung Width/Height:
Ladder Height:
1 Capacity:
310 lbs (141 kg) is the capacity range required by ANSI.
Table 1 – Specifications
One person with a combined weight (clothing, tools, etc.) of no more than 310 lbs (140
kg) per person.
1
Anchorage strength must comply with Section 2.1 requirements.
-40°F (-40°C) Minimum Service Temperature
1,350 lbs (6 kN)
See Figure 1 for the dimensions of each Ladder Anchor model.
See Figure 1 for the weight of each Ladder Anchor model.
Designed to meet the test requirements of OSHA 1926:502, 1910:140.
Materials Count
6100562, 6100564:
Galvanized steel
x1
6100563, 6100565:
Stainless steel
6100562, 6100564:
Galvanized steel
x3
6100563, 6100565:
Stainless steel
x1
Plastic
6100562, 6100564:
Galvanized steel
x1
6100563, 6100565:
Stainless steel
x5
Plastic
6100562, 6100564:
Galvanized steel
x1
6100563, 6100565:
Stainless steel
Cylindrical Rung
Square Rung
Diamond Rung
Angle Iron
Rectangular Rung
For use with the tagline assembly, the ladder must be less than 50 ft (15 m) in length.
Figure 2
Component
Reference
G U-Bolt
H Bolt
I Hex Nut
J Collar Bracket
K Washer
Tagline Pulley
L
Assembly
10.5 in -12.5 in (26.7 cm - 31.8 cm)
0.5 in - 1.5 in (1.3 cm - 3.8 cm) diameter
0.5 in - 1.5 in (1.3 cm - 3.8 cm)
0.5 in - 1.5 in (1.3 cm - 3.8 cm)
0.5 in - 1.5 in (1.3 cm - 3.8 cm)
0.5 in - 1.5 in (1.3 cm - 3.8 cm) height
0.5 in - 1.5 in (1.3 cm - 3.8 cm) width
7
Materials Count
6100562, 6100564:
Galvanized steel
6100563, 6100565:
Stainless steel
6100562, 6100564:
Galvanized steel
6100563, 6100565:
Stainless steel
6100562, 6100564:
Galvanized steel
6100563, 6100565:
Stainless steel
6100562, 6100564:
Galvanized steel
6100563, 6100565:
Stainless steel
6100562, 6100564:
Galvanized steel
6100563, 6100565:
Stainless steel
6100566: Stainless steel
with polypropylene rope
x2
x1
x5
x2
x2
x1