Product Description; System Specifi Cations - 3M DBI SALA 8530538 Manual Del Usuario

:
If you have questions on the use, care, or suitability of this equipment for your application, contact 3M. For general questions, refer to
national Standards including the ANSI Z359 (.0, .1, .2, .3, and .4) family of standards on fall protection, ANSI A10.32, and applicable local, state,
and federal (OSHA) requirements governing occupational safety for more information about fall protection systems.
:
Prior to installation and use of this equipment, record the product identifi cation information from the ID label in the Inspection and
Maintenance Log (Table 2) at the back of this manual.

PRODUCT DESCRIPTION:

Figure 1 illustrates the Flexiguard
boom mounted Glide Rail Fall Arrest Systems that rotate 360° on various base options. Systems with a Counterweight Base can
be transported with a Forklift, Pallet Jack, Crane, etc.
Figure 2 illustrates components of the Adjustable Jib Boom Fall Arrest Systems. See Table 1 for component identifi cation and
specifi cations. The Jib Rail Assembly (A) extends from an Adjustable Upright (B) and supports two Glide Rails (C), each with a
Four-Wheeled Trolley (D) that travels back and forth in the Rail Halves. The Trolley is equipped with a 5/8" Eye for connection of
a Self-Retracting Lifeline or Energy Absorbing Lanyard.
The Adjustable Upright is mounted on a Hitch Ball Post (E) that is embedded in a concrete fi lled Counterweight Base (G). The
height of the Jib Boom is adjusted with a Hand Crank (H) and Lifting Mechanism (I) that raise or lower the Adjustable Upright.
The Adjustable Upright can be rotated 360° with the foldable Rotation Handle (J) and locked at 11° increments with the
Rotation Lock Pin Mechanism (K) or allowed to rotate through a range defi ned by two Rotation Limiters (Q). The bottom of the
Counterweight Base has Lifting Channels (L) and Lifting Eyes (M) for transport with a Forklift, Crane, etc. and Slope Indicators
(O) to ensure the system is level. Optional Leveling Jacks (P) can be installed on the Counterweight Bases.
Component Specifi cations:
Figure 2
Reference Component
Jib Rail Assembly
A
Adjustable Upright Assembly
B
Glide Rail
C
Four-Wheeled Trolley
D
Hitch Ball Post
E
Sleeve
F
Counterweight Base:
G
Hand Crank
H
Lifting Mechanism
I
Rotation Handle
J
Rotation Lock Pin Mechanism
K
Lifting Channels
L
Lifting Eyes
M
Slope Indicators
O
Jack Kit - (Purchase Separately from
P
3M)
Rotation Limiters
Q
System Specifi cations:
Capacity: 1 Person per Glide Trolley with a combined weight (including clothing, tools, etc.) of no more than 420 lbs (191 kg)
Anchorage: Structure supporting the Fall Arrest System must withstand a 12,300 lb (55 kN) vertical load.
Adjustable Jib Boom Fall Arrest Systems. The Adjustable Jib Booms are adjustable height
®
Table 1 – Specifi cations
Materials
Aluminum
Tubes - Steel
Rollers - Nylatron
Lifting Connection Point - Steel
Aluminum Rail Halves
Wheels - Nylon
Bearings - Steel
5/8" Eye - Stainless Steel
Tube - Steel
Hitch Ball Pivot - Steel
Steel
Steel
Concrete with Steel Rebar
Steel
Base - Aluminum
Chain & Chain Cover - Steel
Gears - Steel
Rollers - Plastic
Tube - Steel
Hand Grip - Rubber
Plate - Steel
Pin - Zinc Plated Steel
Steel
Steel
Plastic Gauge on Aluminum
C-Channel
Jack - Steel
Mounting Tubes - Steel
Mounting Pin - Steel
Steel with Magnets
Rating
Connection Point - LIFTING ONLY,
not for Fall Protection: 1,200 lbs
(544 kg) Vertical () Load
1,800 lbs (817 kg) Vertical ()
Load
5,000 lbs (2,268 kg) Vertical ()
Load
Filled with 4,000 psi Concrete:
7,800 lbs (3,538 kg)
For transporting base only. Not
rated for fall arrest.
7,000 lb (3,175 kg) Top Wind
Jacks
9
Assembly/Install
Instruction
5903390
5903390
5903390