Elapsed Time Ring; Tachymeter Ring; Compass Ring - Timex W-223 Guia Del Usuario

TYPE 4
HOUR HAND
STOPWATCH
MINUTE HAND
STOPWATCH
SECOND HAND
BASIC
OPERATIONS
• 6 o'clock eye displays "seconds elapsed" for the chronograph
• 9 o'clock eye displays "minutes elapsed" for the chronograph
• 3 o'clock eye displays the current time in a
24 hour format
TIME
TO SET THE TIME:
NOTE: The stopwatch must be stopped and reset to the zero position prior to
setting the time.
1. Pull the crown out to position B.
2. Rotate the crown either direction until the 24-hour, hour, and minute hands
display the correct time.
3. Push Crown in to position A.
TO ADJUST THE STOPWATCH HANDS TO THE ZERO POSITION:
1. Pull the crown out to position B.
2. Press pusher "A" to move the stopwatch minute and second hands counter
clockwise to the zero position. Press pusher "B" to move the stopwatch
minute and second hands clockwise to the zero position.
3. Push Crown in to position A.
CHRONOGRAPH
THE CHRONOGRAPH IS CAPABLE OF MEASURING:
• Seconds elapsed up to one minute (6 o'clock eye)
• Minutes elapsed up to one hour (9 o'clock eye)
STANDARD CHRONOGRAPH MEASUREMENT
• Press pusher "A" to start timing
• Press pusher "A" to stop timing
• Press pusher "B" to reset the chronograph to the zero position
SPLIT TIME MEASUREMENT
• Press pusher "A" to start timing
• Press pusher "B" to split
• Press pusher "B" to resume timing
• Press pusher "A" to stop timing
• Press pusher "B" to reset the chronograph to the zero position

ELAPSED TIME RING

If your watch is equipped with a rotatable outer ring on the face, with numbers
corresponding to minutes, you can use this Elapsed Time Ring to time an
SECOND HAND
activity from the start, or to mark the ending time for the duration of an activity.
PUSHER "A"
TO TIME AN ACTIVITY FROM THE START:
MINUTE HAND
Set the Start/Stop triangle at the time (hour or minute) when you start the activity
(As shown on the left in the illustration shown below). At completion, you can
CROWN POSITION
see how long the activity took.
NORMAL POSITION "1"
PUSHER "B"
24-HOUR HAND
TO MEASURE THE TIME REMAINING:
Set the triangle to the hour or minute position when you wish to complete the
activity, and check the watch periodically for progress towards that goal.
In the illustration shown on the previous page on the right you can stop when
the minute hand reaches the 20 minutes past the hour position.

TACHYMETER RING

The tachymeter feature can be used to measure speed in miles per hour (MPH),
nautical miles per hour (knots) or kilometers per hour (KPH) using the sweep
second hand and the scale on the wall above the watch face. You need to know
the actual distance you are covering in miles or km.
Start the chronograph with the second hand at zero (the twelve o'clock
position). Within the first minute, the second hand will point to the rate for a one-
mile (or one kilometer) course: if it takes 45 seconds, the hand will point to 80 at
that position – 80 MPH or 80 KPH.
If within the first minute, a distance greater than one mile or kilometer is covered,
multiply the tachymeter number by the distance to get the actual rate: if you
went 1.2 miles in 45 seconds, multiply the 80 by 1.2 – 96 MPH.

COMPASS RING

If your watch is equipped with a movable ring around the dial marked at the
letters "N", "E", "W", "S" (for the four compass directions) or compass degrees,
you can use this feature to find an approximate compass directional reading.
1. Lay the watch on a flat surface, or hold it so that the face is parallel to the
2. Locate the sun and point the hour hand at the sun.
3. In the A.M., rotate the ring until the "S" (south) marker is halfway between
4. In the P.M., rotate the ring until "S" is before the hour hand and halfway
5
ground.
the hour hand and 12:00 (after the hour hand or within the shortest distance
between the hour hand and 12:00).
between the hour hand and 12:00.
12 1
11
10
9
8
7 5
6
ENGLISH
222-095001
2
3
4
N