Manuales relacionados para Kyocera DF-650
Resumen de contenidos para Kyocera DF-650
- Página 1 All manuals and user guides at all-guides.com INSTALLATION GUIDE FOR THE FINISHER GUIDE D’INSTALLATION POUR LE RETOUCHEUR GUIA DE INSTALACION PARA EL FINALIZADOR INSTALLATIONSANLEITUNG FÜR FINISHER GUIDA ALL’INSTALLAZIONE DELLA FINITRICE フィニッシャ設置手順書 DF-650...
- Página 2 All manuals and user guides at all-guides.com...
-
Página 3: Supplied Parts
All manuals and user guides at all-guides.com E Sponge ............ 1 English F Staple cartridges........2 Supplied parts G Staple cartridge (100V model) ....1 H M4 × 20TP Tap Tight S screws ....2 A Finisher............ 1 B Main tray..........1 I Nuts ............ -
Página 4: Procedimiento
All manuals and user guides at all-guides.com Procedure 1. Use the two M4 x 20TP Tap Tight S screws 2. As shown in the illustration, adhere the (H) to secure the connecting plate (D) on the sponge (E) to the top cover of the finisher (A) Before installing the finisher, turn the copier off copier’s output cover (1). - Página 5 All manuals and user guides at all-guides.com 3. Open the front cover. 5. Remove the screw (5) to pull out the con- 4. Remove the screw (2). Pull up the connect- necting rail (6) at the upper part of the fin- ing lever (3) to lower the hooks (4).
- Página 6 All manuals and user guides at all-guides.com 6. Cut out the hole covers (7) at two locations on the copier. 9. Pressing down on the connecting rail (6), 7. Position the finisher (A) and the copier so the long pin (8) of the connecting plate (D) aligns with secure it with the screw (5) you removed in the back hole (9) of the finisher, and the two short pins (10) align with the holes (11) of the con- step 5.
- Página 7 All manuals and user guides at all-guides.com 10. Secure the link lever (3) with the screw (2) 11. Remove the four blue screws (12) locking 13. Remove the fixing tape (16). you removed in step 4. each of the two separate retainers (14) to the intermediate tray (13) and detach both retainers (14).
- Página 8 All manuals and user guides at all-guides.com 14. Remove the fixing tape (17) inside the fin- 15. Raise the release handle (15) to open the 16. Load two staple cartridges (F) into the staple isher. intermediate tray (13). Remove the four holders (19) and (20), and press down on strips of fixing tape (18).
- Página 9 All manuals and user guides at all-guides.com 17. Load the staple cartridge (G) into the staple 19. Insert the two nuts (I) into the main tray (B). holder (21) on the back of the intermediate 20. Secure the main tray (B) with two pins (J). tray (13), and push up on it until it locks 21.
- Página 10 All manuals and user guides at all-guides.com Correcting Paper Curling If the Paper Curls Downward (figure 22. Connect the signal cable (23) to the connec- tor of the copier. “a”) 1. In the non-sort mode, run paper through the 23. Plug the copier’s power cable into an outlet 1.
- Página 11 All manuals and user guides at all-guides.com If the Paper Curls Upward (figure “b”) 4. Run paper through the machine and check if 3. Rotate the upper lever (27) by one scale in it is still curled downward. 1. Open the front cover. the direction of the larger numbers.
- Página 12 All manuals and user guides at all-guides.com Correcting centerfold-stapling (for multi finisher only) 5. Run paper through the machine and check if it is still curled upward. 1. Perform test copies using various paper types. Configure the printer for saddle stapling and output 6.
- Página 13 All manuals and user guides at all-guides.com 3. If the staple position is misaligned, enter 5. Adjust the setting value for each paper size. maintenance mode U248 and perform the If the paper is stapled too far toward the paper eject side (as shown in “c” in the illustration), decrease the setting value.
- Página 14 All manuals and user guides at all-guides.com MEMO...
- Página 15 All manuals and user guides at all-guides.com MEMO...
- Página 16 All manuals and user guides at all-guides.com 2005. 2 303H381010...