Select Blower Option And Install Ductwork; Prepare The Installation - Best PIK33D Instrucciones De Instalación

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

This insert is designed for use with gas or electric outdoor cooking appliances when operated in an outdoor covered patio or
lanai area. As with all electrical appliances, this unit must be protected from the effects of weather.
This unit is not designed for use with a charcoal grill.
The insert model PIK33D must be installed with the interior blower P8D, or with the exterior blower model EB12 or EB15 or with
the in-line blower ILB11 only (sold separately). Other blowers cannot be substituted.
If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 6, 10 up to 13, 15
and up of this manual.
Plan where and how the ductwork will be installed. Access to the top of the insertd is preferred for connection of ductwork. As
an alternative, flexible metal ductwork may be used.
Install 10" steel ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round ductwork, with a short
section (about 4' expanded) of flexible metal duct (optional) for attachment to the transition. Use screws to attach flexible metal
duct to the rigid duct. Use 2" metal foil duct tape to seal duct joints.
The minimum hood distance above cooktop must not be less than 36". A maximum of 42" above cooktop is highly
recommended for best capture of cooking impurities.
Distances over 42" are at the installer and users discretion.
Roof cap
10" round ducts
with 10" round
metal flex. duct
(optional)
9" x 18" to 10"
round transition
Wall cap
36" minimum
above
cooking surface
HH0005A
M P8D
ODEL
I B
NTERIOR LOWER
T D
YPICAL UCTWORK

2. PREPARE THE INSTALLATION

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the
manufacturer.
Make sure that the following items are included:
- Insert
- Accessories:
• Transition (9" x 18" to 10" round)
• 3 Baffle filters
• 2 Shielded halogen bulbs (120 V, 50 W, type GU10)
• Bag of parts including: 3 waterproof wire connectors, 6 no. 10 x 2" hex head screws, 2 wire clamps LP16-AP,
Included in parts bag, but not to be used (please discard): 2 no. 8 x 5/8" screws, 4 no. 10 x 2" flat head screws,
2 wall anchors, 6 washers 3/16" ID x 3/4" OD, 4 stainless steel 10-32 locknuts, 2 no. 8 x 3/8" zinc-plated screws.
Parts sold separately:
- Interior blower P8D with rough-in plate and flow deviator
- Exterior blower assembly EB12 or EB15 (do not use rough-in plate included with exterior blower)
- In-line blower assembly ILB11 (includes rough-in plate and 2 transitions, do not use the rough-in plate)
- Custom hood liner Model L3336D or L3348D (optional)
- Ductwork (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 for a complete list of venting options and
model numbers.
NOTE: During installation, protect countertop and/or cooktop.
Exterior
Insert with
blower
interior
blower
HH0042A
8 no. 8 x 3/8" stainless steel screws.
WARNING
!
Exterior
blower
10" round duct
with 10" round
metal flex. duct
(optional)
9" x 18" to 10"
round transition
Insert
36" minimum
above
cooking surface
M EB12, EB15
ODEL
E B
XTERIOR LOWER
T D
YPICAL UCTWORK
WARNING
!
- 4 -
10" round duct
In-line blower
Insert
10" round
36" minimum
metal flex. duct
above
(optional)
cooking surface
HH0067A
M ILB11
ODEL
I - B
N LINE LOWER
T D
YPICAL UCTWORK
Roof cap
Wall
cap