Martin Yale intimus 689 Instrucciones De Uso página 5

GB
IMPORTANT SAFETY NOTES
<< The machine may not be operated by
more than one person at any given time!
The machine was designed for safe
operation by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine's design and safety concept
are based on adult dimensions (feeder
route, safety cut-off switches, etc.) to ensure
that it can be operated safely by adults
only.
<< Repairs may only be performed by
trained personnel.
COMPENSATION OF THE LIGHT BARRIER:
In order to eliminate malfunctions due to changing
light conditions at the inlet aperture (e.g. by
changing the location) or due to the wear of the
fotocell (scratches), the sensitivity of the light
barrier is automatically re-adjusted by the machine
for the detection of "normal" paper in regular
intervals.
This so called "compensation" can also be carried
out manually in accordance with the sequence
described in the following (e. g. after change of the
light barrier or the PC Board).
The "receptacle full" switch-off must not be
activated for the re-adjustment. The procedure is
as follows:
1. Switch off the maschine at the rocker switch (1)
and open the door.
2. Press the pushbutton switch "reverse" (3) and
keep it pressed.
3. Press the "ready" rocker switch (1).
4. Release the "reverse" pushbutton switch (3)
after approx. 3 sec.
5. Push switching flap „receptacle full" backwards
for at least 3 sec.
6. Close the door after approx. 3 sec.
7. Cover the light barrier with a piece of paper (do
not feed the paper up to the cutter) and wait until
the motor is switched on.
This completes the compensation. The machine
is now ready for operation.
SPECIAL ACCESSORIES
Description
Plastic bag, 700 x 500 x 1200 x 0,06 mm
Lubrication bottle, 125 ml
Second deposit tray cpl., silver gray
Second deposit tray cpl., chrome plated
Receptacle, 625 x 480 x 660 mm
Note: For orders of special accessories and spare parts, please contact your dealer.
<< Never insert fingers into opening.
Serious injury may result!
<< In case of danger switch the
STOP machine off with the mains switch,
or with the emergency switch, or
unplug the machine.
<< Always unplug the machine from
the mains power supply before
opening the machine.
MAINTENANCE
Note: If the compensation process has been
interfered with due to exessive external incident
light (direct sun light, lamps, spots etc.) or due to
a false procedure, keep the external light away
from light barrier and re-start the compensation
process right from the beginning.
CLEANING THE PHOTOCELLS:
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes" of the photocell with a brush.
MAINTENANCE CUTTING BLOCK:
After approximately 15 minutes of continuous
use, run the cutting system in reverse for 15 to 20
seconds and spray some of the enclosed Special
Oil onto the cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (rocker switch (1) (fig. 1).
<< Keep all loose articles of
clothing, ties, jewelery,
long hair or other loose
objects away from
opening, injury may
result!
Order-No.
99954
99943
30712
30702
75987
5
MALFUNCTION
PAPER JAM:
If too much paper is fed to the cutting system the
machine will react as follows:
- The cutting system blocks and then stops.
- The pilot lamp of the stop-putton „S" (3) (fig. 2)
will light.
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(4) (fig. 2).
- The cutting mechanism then runs backwards
and returns the excess material.
- Remove excess paper from the machine and
continue shredding with less paper.
Important: After any paper jam, make certain the
cutting mechanism is free to operate in both free
(particles have jammed between the cutters and
the scraper), spray some of the special oil supplied
with the machine through the feed slot onto the
cutting mechanism while alternating between
forward and reverse modes until the machine is
free.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with the
rocker switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the following:
- is the plug connected to the mains?
- is the rocker switch (1) on?
- is the door closed?
- is the collecting bag full?
The bag has to be emptied.
- is there a paper jam?
Follow the instructions under „paper jam".
- has the motor been overloaded?
Wait until the motor has cooled, and then restart.
If none of the above applies, please contact
your dealer.
TECHNICAL DATA
Cutting width:
007SL: 0.65x1.5–5 mm
(cross-cut)
007SF: 0.8x4.5 mm
(cross-cut)
Cutting capacity:
007SL: 10–12 sheets *
007SF: 8–10 sheets *
Working width:
007SL: 300 mm
007SF: 380 mm
Power consumption: 2 kW
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/50Hz: 16 A
240V/50Hz: 13 A
120V/60Hz: 20 A
100V/50/60Hz: 20 A
Width: 700 mm
Depht: 550 mm
Height: 1115 mm
Noise level: approx. 70 dB(A)
Weight:
007SL: approx. 170 kg
007SF: approx. 142 kg
*
Capacity may vary depending upon paper
weight, grain and power.