Publicidad
Safety Instructions (continued)
10. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
11. If the equipment should start to
vibrate abnormally, STOP the
engine/motor and check immediately
for the cause. Vibration is generally a
warning of trouble.
NEVER refuel a running
or hot engine. Explosive fuel
can cause fires and severe
burns. Avoid overfilling fuel
tank.
12. Check fuel level before starting the
engine. Do not fill the gas tank
indoors. Wipe off any spilled gas
before starting the engine.
Gasoline vapor is highly flam-
mable. Refill outdoors or only in
well ventilated areas. Do not
store, spill or use gasoline near
an open flame or heat devices
such as a stove, furnace, or
water heater, which utilize a
pilot light, or any device that
can create a spark. If gasoline
is accidentally spilled, move
unit away from the spill area
and avoid creating any source
of ignition until gasoline vapors
have dissipated.
Motors, electrical equip-
ment and controls can cause
electrical arcs that will ignite a
flammable gas or vapor. Never
operate or repair in or near a
flammable gas or vapor. Never
store flammable liquids or
gases in the vicinity of the com-
pressor.
Carbon monoxide can
cause severe nausea, fainting
or death. Do not operate unit
inside a closed building or a
poorly ventilated area.
13. To reduce fire hazard, keep
engine/motor exterior free of oil, sol-
vent, or excessive grease.
Never remove or attempt to
adjust safety valve. Keep safety
valve free from paint and other
accumulations.
14. Do not tamper with governor setting
on engine. Overspeeding the unit
severely shortens engine life and may
also be very hazardous.
Never attempt to repair
or modify a tank! Welding,
drilling or any other modifica-
tion will weaken the tank result-
ing in damage from rupture or
explosion. Always replace worn
or damaged tanks.
15. Tanks rust from moisture build-up,
which weakens the tank. Make sure to
drain tank daily and inspect periodical-
ly for unsafe conditions such as rust
formation and corrosion.
4
Pièces de rechange
Pour les pièces de rechange, appeler le 1-800-4-RIDGID
S'il vous plaît fournir l'information suivant:
-Numéro du modèle
-Numéro de série (si applicable)
-Description de la pièce et son numéro sur la liste de pièces
No.
No de
Numéro
Ref.
catalogue
de pièce
1
17993
BG220901SJ
2
17998
ST026200AV
3
18003
BT023100AV
4
17703
WL026100AV
5
—
ST070827AV
N
6
—
N
7
—
8
17798
V-215108AV
9
17783
ST071626AV
10
18028
ST160002AV
11
17913
D-1403
12
17918
ST073612AV
13
18033
AR053400CG
14
17853
ST158300AV
15
18038
ST116400AV
16
18043
AA021800AV
17
18048
ST073613AV
18
18053
WA005501AV
19
18058
CV006412AV
20
18063
ST128415AV
21
17878
GA016709AV
22
17873
HF203300AV
23
17793
WL024501AV
24
17773
GA016705AV
25
18068
VT472200AJ
26
18073
ST186600AV
27
18078
PU015901SJ
28
18083
PU015400AV
29
18088
KE000900AV
30
18093
ST012200AV
31
18098
BG208800AJ
32
18103
NG002502AV
33
18108
ST070625AV
34
18113
ST011200AV
35
18118
AL014000AV
36
18123
ST164100AV
37
20978
ST033500AV
38
20983
ST084704AV
39
22788
BG210000AV
40
22793
ST070674AV
41
20423
ST016000AV
42
18113
ST011200AV
43
20428
ST146001AV
44
21003
BG220400AV
45
21008
ST073278AV
46
22783
ST076829AV
NÉCESSAIRES DE RÉPARATION
N
22098
VT273500AJ
Consideré un article sujet à l'usure.
*
F
Article normal de quincaillerie - disponible à votre quincaillerie locale
Description
Montage du dispositif de protection de
la courroie (#37 - 46 compris)
Vis de pression
* Courroie (4L510)
Filtre équipé
Vis
Tube de nylon de 3/8 po
Raccord à coude
Soupape de sûreté ASME
Vis torx
* Poignée de manche
* Robinet de purge
Fiche
Réservoir d'air
* Pied en caoutchouc
Vis
Tige d'arbre de roue
Bouchon
* Roue pneumatique 10" (2,54 cm)
* Commande d'obturateur
* Déchargeur d'obturateur
* Manomètre, Sortie
* Raccord
* Ensemble rég. (inclut 21, 22 et 24)
* Manomètre, Réservoir
Pompe
Tuyau de décharge
Volant
Poulie
Clé 3⁄16 po
Vis de pression à tête carrée
Assemblage d'ancre
Moteur
Vis à tête hexagonale
Rondelle
Contre-écrou
Dispositif de retenue des fils
Écrou à collet de 3/8 po
Boulon d'épaulement de 3/8 po
Fixation de protecteur de courroie (Moteur)
Boulon, 5/16 po - 24 x 1/2 po
Vis, 5/16 po - 18 x 3/4 po
Rondelle 5/16 po
Écrou, 5/16 po - 18
Fixation de protecteur de courroie (Pompe)
Attache de carter de courroie
Boulon, M8 - 1.25 x 30
Nécessaire de tubes
Fr21
Qté
1
1
1
1
4
1
2
1
4
2
2
2
1
4
4
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
8
4
1
1
1
1
1
1
1
1
1
8
1
1
Publicidad
Capítulos
